The effect of surface roughness and wettability on the adhesion and proliferation of Saos-2 cells seeded on 3D printed poly(3-hydroxybutyrate)/polylactide (PHB/PLA) surfaces

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68378041%3A_____%2F24%3A00603602" target="_blank" >RIV/68378041:_____/24:00603602 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/00216305:26310/24:PU151891

Výsledek na webu

<a href="https://www.sciencedirect.com/science/article/pii/S2666845924000916?via%3Dihub" target="_blank" >https://www.sciencedirect.com/science/article/pii/S2666845924000916?via%3Dihub</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1016/j.rsurfi.2024.100271" target="_blank" >10.1016/j.rsurfi.2024.100271</a>

Jazyk výsledku

angličtina

Název v původním jazyce

The effect of surface roughness and wettability on the adhesion and proliferation of Saos-2 cells seeded on 3D printed poly(3-hydroxybutyrate)/polylactide (PHB/PLA) surfaces

Popis výsledku v původním jazyce

The aim of this work is to explore the effect of surface characteristics of the 3D printed scaffolds on their suitability for Saos-2 cells growth. Two promising materials for bone tissue engineering were examined, both containing poly(3-hydroxybutyrate)/poly(d,l-lactide) plasticized blend and one of them filled with bioactive tricalcium phosphate. The surface free energy (SFE) of samples was determined by contact angle measurement with four liquids. For non-filled sample the water contact angle (WCA) was 74° and its SFE was 40 mN m−1. The composite sample exhibited substantially decreased WCA, 61°. Moreover, the addition of the tricalcium phosphate caused doubling of the polar component of the SFE which increased by a total of 13%. 3D printed surfaces prepared by fused deposition modeling method showed a profound increase of WCA due to the increase in their surface roughness which was analyzed by confocal microscopy. The change in wetting properties strongly affected the behavior of Saos-2 cells on printed surfaces. The number of cells as measured by DNA quantification linearly decreased with increasing surface WCA. The highest number of cells was observed on the pressed samples and 3D printed surfaces made of simple lines and a grid with 50 μm gap between lines. The favored surfaces exhibit WCA under 80° which is important information for the future design of the scaffolds.

Název v anglickém jazyce

The effect of surface roughness and wettability on the adhesion and proliferation of Saos-2 cells seeded on 3D printed poly(3-hydroxybutyrate)/polylactide (PHB/PLA) surfaces

Popis výsledku anglicky

The aim of this work is to explore the effect of surface characteristics of the 3D printed scaffolds on their suitability for Saos-2 cells growth. Two promising materials for bone tissue engineering were examined, both containing poly(3-hydroxybutyrate)/poly(d,l-lactide) plasticized blend and one of them filled with bioactive tricalcium phosphate. The surface free energy (SFE) of samples was determined by contact angle measurement with four liquids. For non-filled sample the water contact angle (WCA) was 74° and its SFE was 40 mN m−1. The composite sample exhibited substantially decreased WCA, 61°. Moreover, the addition of the tricalcium phosphate caused doubling of the polar component of the SFE which increased by a total of 13%. 3D printed surfaces prepared by fused deposition modeling method showed a profound increase of WCA due to the increase in their surface roughness which was analyzed by confocal microscopy. The change in wetting properties strongly affected the behavior of Saos-2 cells on printed surfaces. The number of cells as measured by DNA quantification linearly decreased with increasing surface WCA. The highest number of cells was observed on the pressed samples and 3D printed surfaces made of simple lines and a grid with 50 μm gap between lines. The favored surfaces exhibit WCA under 80° which is important information for the future design of the scaffolds.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

30404 - Biomaterials (as related to medical implants, devices, sensors)

Projekt

<a href="/cs/project/EH22_008%2F0004562" target="_blank" >EH22_008/0004562: Excelentní výzkum v regenerativní medicíně</a><br>

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2024

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Results in Surfaces and Interfaces

ISSN

2666-8459

e-ISSN

—

Svazek periodika

16

Číslo periodika v rámci svazku

August

Stát vydavatele periodika

NL - Nizozemsko

Počet stran výsledku

11

Strana od-do

100271

Kód UT WoS článku

001334582100001

EID výsledku v databázi Scopus

2-s2.0-85201513467