Effect of alloying elements on the reactive sintering behaviour of NiTi alloy

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68378271%3A_____%2F17%3A00474070" target="_blank" >RIV/68378271:_____/17:00474070 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/68407700:21340/17:00319398

Výsledek na webu

<a href="http://dx.doi.org/10.4028/www.scientific.net/MSF.891.447" target="_blank" >http://dx.doi.org/10.4028/www.scientific.net/MSF.891.447</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/MSF.891.447" target="_blank" >10.4028/www.scientific.net/MSF.891.447</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Effect of alloying elements on the reactive sintering behaviour of NiTi alloy

Popis výsledku v původním jazyce

NiTi alloy is usually prepared by casting and forming. As an innovative process, reactive sintering powder metallurgy is tested worldwide, aiming to prepare pure NiTi alloy easily from nickel and titanium powders. This process enables to prepare both porous and low-porosity alloy, depending on the process conditions. However, the formation of NiTi phase in this process is always accompanied by the Ti2Ni phase, which is hard, brittle, less corrosion resistant and does not have the shape memory. In this work, various alloying elements (Al, Si, Mg, Fe, Nb, V) were added to Ni-Ti alloy in order to lower the amount of Ti2Ni phase or at least to minimize its undesirable effect on the alloy properties. The reactive sintering behaviour, phase composition and mechanical properties of Ni-Ti-X alloys were described.

Název v anglickém jazyce

Effect of alloying elements on the reactive sintering behaviour of NiTi alloy

Popis výsledku anglicky

NiTi alloy is usually prepared by casting and forming. As an innovative process, reactive sintering powder metallurgy is tested worldwide, aiming to prepare pure NiTi alloy easily from nickel and titanium powders. This process enables to prepare both porous and low-porosity alloy, depending on the process conditions. However, the formation of NiTi phase in this process is always accompanied by the Ti2Ni phase, which is hard, brittle, less corrosion resistant and does not have the shape memory. In this work, various alloying elements (Al, Si, Mg, Fe, Nb, V) were added to Ni-Ti alloy in order to lower the amount of Ti2Ni phase or at least to minimize its undesirable effect on the alloy properties. The reactive sintering behaviour, phase composition and mechanical properties of Ni-Ti-X alloys were described.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/GA14-03044S" target="_blank" >GA14-03044S: Příprava slitin NiTi s tvarovou pamětí reaktivní sintrací</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Materials Science Forum

ISBN

9783035710182

ISSN

0255-5476

e-ISSN

—

Počet stran výsledku

5

Strana od-do

447-451

Název nakladatele

Trans Tech Publications Ltd

Místo vydání

Zürich

Místo konání akce

Stará Lesná

Datum konání akce

20. 4. 2016

Typ akce podle státní příslušnosti

EUR - Evropská akce

Kód UT WoS článku

—