Effect of topology parameters on physical–mechanical properties of magnetic PLA 3D-printed structures

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68378297%3A_____%2F23%3A00579993" target="_blank" >RIV/68378297:_____/23:00579993 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/61989100:27230/23:10253823 RIV/75081431:_____/23:00002624

Výsledek na webu

<a href="https://doi.org/10.3390/magnetochemistry9120232" target="_blank" >https://doi.org/10.3390/magnetochemistry9120232</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/magnetochemistry9120232" target="_blank" >10.3390/magnetochemistry9120232</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Effect of topology parameters on physical–mechanical properties of magnetic PLA 3D-printed structures

Popis výsledku v původním jazyce

This work aims to characterize 3D-printed structures composed of a thermoplastic material (polylactic acid (PLA)) containing a combination of magnetic particles composed of iron(III) oxide (hematite) and iron(II)–iron (III) oxide (magnetite) with various infill densities and print orientations in regard to their possible processing by Fused Filament Fabrication additive technology. The correct processing temperatures have been determined using thermal analysis, and the paramagnetic and mechanical properties of the samples have been tested. The relative permeability has been identified to be strongly dependent on the topology parameters of the tested samples. The results of the inductance values for the samples without magnetic additives (infill densities 50% and 100%) have been detected to be comparable - nonetheless, the magnetic samples with 100% infill density has been found to be about 50% higher. A similar trend has been observed in the case of the values of the relative permeability, where the magnetic samples with 100% infill density have been measured as having an about 40% increased relative permeability in the comparison with the samples without magnetic additives (infill densities 20–100%). Finite Element Modelling (FEM) simulations have been applied to determine the magnetic field distributions and, moreover, to calculate the holding forces of all the printed samples. The maximum value of the holding force for the minimum distance of the plastic plate has been found to reach a value of almost 300 N (magnetic sample with 100% infill density). The obtained comprehensive characterization of the printed samples may be utilized for designing and tuning the desired properties of the samples needed in various industrial applications.

Název v anglickém jazyce

Effect of topology parameters on physical–mechanical properties of magnetic PLA 3D-printed structures

Popis výsledku anglicky

This work aims to characterize 3D-printed structures composed of a thermoplastic material (polylactic acid (PLA)) containing a combination of magnetic particles composed of iron(III) oxide (hematite) and iron(II)–iron (III) oxide (magnetite) with various infill densities and print orientations in regard to their possible processing by Fused Filament Fabrication additive technology. The correct processing temperatures have been determined using thermal analysis, and the paramagnetic and mechanical properties of the samples have been tested. The relative permeability has been identified to be strongly dependent on the topology parameters of the tested samples. The results of the inductance values for the samples without magnetic additives (infill densities 50% and 100%) have been detected to be comparable - nonetheless, the magnetic samples with 100% infill density has been found to be about 50% higher. A similar trend has been observed in the case of the values of the relative permeability, where the magnetic samples with 100% infill density have been measured as having an about 40% increased relative permeability in the comparison with the samples without magnetic additives (infill densities 20–100%). Finite Element Modelling (FEM) simulations have been applied to determine the magnetic field distributions and, moreover, to calculate the holding forces of all the printed samples. The maximum value of the holding force for the minimum distance of the plastic plate has been found to reach a value of almost 300 N (magnetic sample with 100% infill density). The obtained comprehensive characterization of the printed samples may be utilized for designing and tuning the desired properties of the samples needed in various industrial applications.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

10302 - Condensed matter physics (including formerly solid state physics, supercond.)

Projekt

<a href="/cs/project/EF17_049%2F0008407" target="_blank" >EF17_049/0008407: Inovativní a aditivní technologie výroby - nová technologická řešení 3D tisku kovů a kompozitních materiálů</a><br>

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2023

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Magnetochemistry

ISSN

2312-7481

e-ISSN

2312-7481

Svazek periodika

9

Číslo periodika v rámci svazku

12

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

14

Strana od-do

232

Kód UT WoS článku

001130893300001

EID výsledku v databázi Scopus

2-s2.0-85180422225