Cement Pastes Prepared from CEM II: Measuring the Creep

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21110%2F10%3A00176518" target="_blank" >RIV/68407700:21110/10:00176518 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Cement Pastes Prepared from CEM II: Measuring the Creep

Popis výsledku v původním jazyce

Material properties give a possibility of mathematical modeling the material. Creep of cement paste is possible integrate into the basic properties, which is important not only for modeling, but for design of structures, too. In the paper are described experimental results of measuring of the cement pastes creep. For measuring was used the cement CEM II and prepared pastes with water cement ratio from 0.3 to 0.5. Creep of pastes was measured on water saturated and water dried specimens. Shrinkage of different cement pastes was measured, too. Mechanical properties of pastes were measured after finishing of creep tests. Dimensions of cylindrical specimens were 10mm in diameter and 70 mm in length. Cylinders were tested in the special creep test equipmentand in the electromechanical testing equipment for the uniaxial compression tests. History of creep, material properties, history of specimens were used like an inputs for simulation by finite element method.

Název v anglickém jazyce

Cement Pastes Prepared from CEM II: Measuring the Creep

Popis výsledku anglicky

Material properties give a possibility of mathematical modeling the material. Creep of cement paste is possible integrate into the basic properties, which is important not only for modeling, but for design of structures, too. In the paper are described experimental results of measuring of the cement pastes creep. For measuring was used the cement CEM II and prepared pastes with water cement ratio from 0.3 to 0.5. Creep of pastes was measured on water saturated and water dried specimens. Shrinkage of different cement pastes was measured, too. Mechanical properties of pastes were measured after finishing of creep tests. Dimensions of cylindrical specimens were 10mm in diameter and 70 mm in length. Cylinders were tested in the special creep test equipmentand in the electromechanical testing equipment for the uniaxial compression tests. History of creep, material properties, history of specimens were used like an inputs for simulation by finite element method.

Druh

D - Stať ve sborníku

CEP obor

JN - Stavebnictví

OECD FORD obor

—

Projekt

<a href="/cs/project/GA103%2F08%2F1492" target="_blank" >GA103/08/1492: Virtuální testy dotvarování betonu</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2010

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Konštrukčné a fyzikálne aspekty stavebného inžinierstva, 2010

ISBN

978-80-553-0527-1

ISSN

—

e-ISSN

—

Počet stran výsledku

8

Strana od-do

—

Název nakladatele

Technická univerzita v Košiciach

Místo vydání

Košice

Místo konání akce

Štrbské pleso

Datum konání akce

24. 11. 2010

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—