Design of Portable Device for Rapid Temperature Testing of Concrete Specimens: System Circuit Design Phase
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21110%2F14%3A00221872" target="_blank" >RIV/68407700:21110/14:00221872 - isvavai.cz</a>
Výsledek na webu
<a href="http://dx.doi.org/10.4028/www.scientific.net/AMR.1054.11" target="_blank" >http://dx.doi.org/10.4028/www.scientific.net/AMR.1054.11</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.4028/www.scientific.net/AMR.1054.11" target="_blank" >10.4028/www.scientific.net/AMR.1054.11</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Design of Portable Device for Rapid Temperature Testing of Concrete Specimens: System Circuit Design Phase
Popis výsledku v původním jazyce
The project described in this paper is based on sequential development of a temperature controlled weather condition emulator for testing of concrete samples in different temperature levels at varying period of time. The device can be used to test concrete samples when engineer wants to realize the concrete behaviour under extreme conditions such as cold, very high temperature or drastic drops of temperature incurred in a short period and importantly test for concrete samples during hydration. As an initial phase of the development process, entire system architecture is sub-phased to modular form and hence formulated each module for simulation before realizing of the final fabrication of the actual system. The main objective in this phase is to designthe electronic circuit to control the attached thermoelectric Peltier which is the main subject of the heat source temperature controller. Since, mathematical modelling of dynamics of the Peltier systems are not well defined and assured t
Název v anglickém jazyce
Design of Portable Device for Rapid Temperature Testing of Concrete Specimens: System Circuit Design Phase
Popis výsledku anglicky
The project described in this paper is based on sequential development of a temperature controlled weather condition emulator for testing of concrete samples in different temperature levels at varying period of time. The device can be used to test concrete samples when engineer wants to realize the concrete behaviour under extreme conditions such as cold, very high temperature or drastic drops of temperature incurred in a short period and importantly test for concrete samples during hydration. As an initial phase of the development process, entire system architecture is sub-phased to modular form and hence formulated each module for simulation before realizing of the final fabrication of the actual system. The main objective in this phase is to designthe electronic circuit to control the attached thermoelectric Peltier which is the main subject of the heat source temperature controller. Since, mathematical modelling of dynamics of the Peltier systems are not well defined and assured t
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
JM - Inženýrské stavitelství
OECD FORD obor
—
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2014
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
Special Concrete and Composites 2014
ISBN
978-3-03835-317-1
ISSN
1022-6680
e-ISSN
—
Počet stran výsledku
6
Strana od-do
11-16
Název nakladatele
Trans Tech Publications
Místo vydání
Uetikon-Zurich
Místo konání akce
Skalský Dvůr
Datum konání akce
16. 10. 2014
Typ akce podle státní příslušnosti
EUR - Evropská akce
Kód UT WoS článku
000348436200003