Optimization of Processing Parameters of Medium Density Fiberboard Using Response Surface Methodology for Multiwalled Carbon Nanotubes as a Nanofiller

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21110%2F17%3A00311421" target="_blank" >RIV/68407700:21110/17:00311421 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/68407700:21720/17:00311421

Výsledek na webu

<a href="http://dx.doi.org/10.1007/s00107-016-1106-2" target="_blank" >http://dx.doi.org/10.1007/s00107-016-1106-2</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/s00107-016-1106-2" target="_blank" >10.1007/s00107-016-1106-2</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Optimization of Processing Parameters of Medium Density Fiberboard Using Response Surface Methodology for Multiwalled Carbon Nanotubes as a Nanofiller

Popis výsledku v původním jazyce

In the present work, medium density fiberboard (MDF) panels were produced using multiwalled carbon nanotubes (MWCNT) reinforced urea formaldehyde resin. Response surface methodology was employed to optimize the relationship between the three variables, viz. pressing time, percentage of UF resin and percentage of MWCNT, used in the fabrication of MDF, and the influence of variables on the internal bonding (IB) and modulus of rupture (MOR) was studied. The optimum conditions based on the IB strength were determined as 8.18 % of UF resin, pressing time of 232 s, and MWCNT of 3.5 %. Similarly, the optimized conditions for MOR are also reported in this paper.

Název v anglickém jazyce

Optimization of Processing Parameters of Medium Density Fiberboard Using Response Surface Methodology for Multiwalled Carbon Nanotubes as a Nanofiller

Popis výsledku anglicky

In the present work, medium density fiberboard (MDF) panels were produced using multiwalled carbon nanotubes (MWCNT) reinforced urea formaldehyde resin. Response surface methodology was employed to optimize the relationship between the three variables, viz. pressing time, percentage of UF resin and percentage of MWCNT, used in the fabrication of MDF, and the influence of variables on the internal bonding (IB) and modulus of rupture (MOR) was studied. The optimum conditions based on the IB strength were determined as 8.18 % of UF resin, pressing time of 232 s, and MWCNT of 3.5 %. Similarly, the optimized conditions for MOR are also reported in this paper.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20101 - Civil engineering

Projekt

<a href="/cs/project/LO1605" target="_blank" >LO1605: Univerzitní centrum energeticky efektivních budov – Fáze udržitelnosti</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

European Journal of Wood and Wood Products

ISSN

0018-3768

e-ISSN

1436-736X

Svazek periodika

75

Číslo periodika v rámci svazku

2

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

11

Strana od-do

203-213

Kód UT WoS článku

000394358700006

EID výsledku v databázi Scopus

2-s2.0-84991830745