SHS and RHS stainless steel slender members loaded by compression and bending interaction

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21110%2F17%3A00313563" target="_blank" >RIV/68407700:21110/17:00313563 - isvavai.cz</a>

Výsledek na webu

<a href="http://iopscience.iop.org/article/10.1088/1757-899X/236/1/012064" target="_blank" >http://iopscience.iop.org/article/10.1088/1757-899X/236/1/012064</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1088/1757-899X/236/1/012064" target="_blank" >10.1088/1757-899X/236/1/012064</a>

Jazyk výsledku

angličtina

Název v původním jazyce

SHS and RHS stainless steel slender members loaded by compression and bending interaction

Popis výsledku v původním jazyce

Behaviour of stainless steel slender members loaded by interaction of axial compressive force and bending moment is investigated in this research. Square hollow sections (SHS) made of austenitic stainless steel grade are considered. An initial numerical parametric study in FE software Abaqus is given and its results are compared to the existing design procedures and design standard rules. The investigated parameters are mainly the column slenderness, section slenderness, ratio between the applied bending moment and axial compressive force and the moment distribution along the member. The necessity of having additional design rules for stainless steels is firstly demonstrated on the values of interaction factors ky which are significantly higher for stainless steel members due to the material nonlinearity with decreased stiffness even at lower stress levels. As an alternative, the General Method is used for comparison to the Abaqus GMNIA model results. The limitation of the method when used for members of non-linear material behaviour is shown and a safe modification of design procedure is suggested.

Název v anglickém jazyce

SHS and RHS stainless steel slender members loaded by compression and bending interaction

Popis výsledku anglicky

Behaviour of stainless steel slender members loaded by interaction of axial compressive force and bending moment is investigated in this research. Square hollow sections (SHS) made of austenitic stainless steel grade are considered. An initial numerical parametric study in FE software Abaqus is given and its results are compared to the existing design procedures and design standard rules. The investigated parameters are mainly the column slenderness, section slenderness, ratio between the applied bending moment and axial compressive force and the moment distribution along the member. The necessity of having additional design rules for stainless steels is firstly demonstrated on the values of interaction factors ky which are significantly higher for stainless steel members due to the material nonlinearity with decreased stiffness even at lower stress levels. As an alternative, the General Method is used for comparison to the Abaqus GMNIA model results. The limitation of the method when used for members of non-linear material behaviour is shown and a safe modification of design procedure is suggested.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20102 - Construction engineering, Municipal and structural engineering

Projekt

<a href="/cs/project/GA17-24769S" target="_blank" >GA17-24769S: Nelineární stabilita a pevnost štíhlých konstrukcí s nelineárními materiálovými vlastnostmi.</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Building up Efficient and Sustainable Transport Infrastructure 2017 (BESTInfra2017)

ISBN

—

ISSN

1757-8981

e-ISSN

1757-899X

Počet stran výsledku

8

Strana od-do

—

Název nakladatele

IOP Publishing Ltd

Místo vydání

Bristol

Místo konání akce

Praha

Datum konání akce

20. 9. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

000417428700064