Alkali-activated slag with 3D printing waste: Self-heating potential pretests
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21110%2F23%3A00369554" target="_blank" >RIV/68407700:21110/23:00369554 - isvavai.cz</a>
Výsledek na webu
<a href="https://doi.org/10.1063/5.0162601" target="_blank" >https://doi.org/10.1063/5.0162601</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1063/5.0162601" target="_blank" >10.1063/5.0162601</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Alkali-activated slag with 3D printing waste: Self-heating potential pretests
Popis výsledku v původním jazyce
The basic premise of self-heating function of construction materials is favorable electrical properties, which is not fulfilled in the case of common geopolymers, cementitious or alkali-activated materials. To gain self-heating ability of such materials, an optimized amount of metal- or carbon-based admixtures is used to form electrically conductive paths which in case of higher amount of admixture results in a significant increase in electrical conductivity. It was reported at low voltage load an outstanding self-heating ability of cementitious composites with nickel powder. Nevertheless, such composites are of high environmental impact due to cement and nickel production. Therefore, it is beneficial to seek promising self-heating construction materials based on byproducts or wastes. The paper is focused on metallic 3D printing waste characterization and the determination of electrical and thermal properties of alkali-activated slag mortar with 3D printing waste. It was proved by measurements of electrical properties and confirmed by measurement of volt-ampere characteristics in the range of 40 to 100 V that even a high dosage of 3D printing waste admixture rich on nickel alloys, that the effective electrical conductivity of the composite is not sufficient to allow meaningful self-heating ability.
Název v anglickém jazyce
Alkali-activated slag with 3D printing waste: Self-heating potential pretests
Popis výsledku anglicky
The basic premise of self-heating function of construction materials is favorable electrical properties, which is not fulfilled in the case of common geopolymers, cementitious or alkali-activated materials. To gain self-heating ability of such materials, an optimized amount of metal- or carbon-based admixtures is used to form electrically conductive paths which in case of higher amount of admixture results in a significant increase in electrical conductivity. It was reported at low voltage load an outstanding self-heating ability of cementitious composites with nickel powder. Nevertheless, such composites are of high environmental impact due to cement and nickel production. Therefore, it is beneficial to seek promising self-heating construction materials based on byproducts or wastes. The paper is focused on metallic 3D printing waste characterization and the determination of electrical and thermal properties of alkali-activated slag mortar with 3D printing waste. It was proved by measurements of electrical properties and confirmed by measurement of volt-ampere characteristics in the range of 40 to 100 V that even a high dosage of 3D printing waste admixture rich on nickel alloys, that the effective electrical conductivity of the composite is not sufficient to allow meaningful self-heating ability.
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
—
OECD FORD obor
20501 - Materials engineering
Návaznosti výsledku
Projekt
<a href="/cs/project/GA19-11516S" target="_blank" >GA19-11516S: Geopolymery pro sofistikované aplikace ve stavebnictví</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2023
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
International Conference of Numerical Analysis and Applied Mathematics ICNAAM 2021
ISBN
978-0-7354-4589-5
ISSN
0094-243X
e-ISSN
1551-7616
Počet stran výsledku
5
Strana od-do
—
Název nakladatele
AIP Publishing
Místo vydání
Melville, NY
Místo konání akce
Rodos
Datum konání akce
20. 9. 2021
Typ akce podle státní příslušnosti
WRD - Celosvětová akce
Kód UT WoS článku
—