APPLICATION OF X-RAY DIFFRACTION IN DEVELOPMENT OF NEW TYPE OF MOULDS FOR PRODUCTION OF REFRACTORY AND HIGHLY ABRASIVE OBJECTS

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21220%2F13%3A00214492" target="_blank" >RIV/68407700:21220/13:00214492 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/68407700:21340/13:00214492

Výsledek na webu

<a href="http://www.mmscience.eu/archives/MM_Science_201304.pdf" target="_blank" >http://www.mmscience.eu/archives/MM_Science_201304.pdf</a>

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

APPLICATION OF X-RAY DIFFRACTION IN DEVELOPMENT OF NEW TYPE OF MOULDS FOR PRODUCTION OF REFRACTORY AND HIGHLY ABRASIVE OBJECTS

Popis výsledku v původním jazyce

Ceramic materials can be used due to their high hardness and chemical stability as both the wear and corrosion resistant coatings. Their deposition on moulds for manufacturing of objects from refractory and highly abrasive materials is challenging, because they are traditionally made from hard-to-blast case-hardened tool steels with hardness exceeding 60 HRC. The pressing processes impose further stringent requirements on the coating microstructure; especially in respect to its homogeneity, cohesion andwear resistance. Considering results of laboratory analyses of residual stresses and roughness of blasted surfaces, mould plates from low-carbon C45 steel were sprayed with five different ceramic materials by water stabilized plasma gun. The testing ofthe moulds with plasma coatings was performed on-site in a factory under standard pressing conditions.

Název v anglickém jazyce

APPLICATION OF X-RAY DIFFRACTION IN DEVELOPMENT OF NEW TYPE OF MOULDS FOR PRODUCTION OF REFRACTORY AND HIGHLY ABRASIVE OBJECTS

Popis výsledku anglicky

Ceramic materials can be used due to their high hardness and chemical stability as both the wear and corrosion resistant coatings. Their deposition on moulds for manufacturing of objects from refractory and highly abrasive materials is challenging, because they are traditionally made from hard-to-blast case-hardened tool steels with hardness exceeding 60 HRC. The pressing processes impose further stringent requirements on the coating microstructure; especially in respect to its homogeneity, cohesion andwear resistance. Considering results of laboratory analyses of residual stresses and roughness of blasted surfaces, mould plates from low-carbon C45 steel were sprayed with five different ceramic materials by water stabilized plasma gun. The testing ofthe moulds with plasma coatings was performed on-site in a factory under standard pressing conditions.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JG - Hutnictví, kovové materiály

OECD FORD obor

—

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2013

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

MM Science Journal

ISSN

1803-1269

e-ISSN

—

Svazek periodika

2

Číslo periodika v rámci svazku

June

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

4

Strana od-do

396-399

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—