Influence of preheating and heat treatment after welding according to the EN 13445 and ASME Code on the hardness level of welded joints for the Pressure Vessel Plates
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21220%2F14%3A00224866" target="_blank" >RIV/68407700:21220/14:00224866 - isvavai.cz</a>
Nalezeny alternativní kódy
RIV/44555601:13420/14:43886592
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Influence of preheating and heat treatment after welding according to the EN 13445 and ASME Code on the hardness level of welded joints for the Pressure Vessel Plates
Popis výsledku v původním jazyce
The paper deals with an analysis of preheating and heat treatment after welding and their influence on the final hardness level in case of welded jonits for common materials applied for manufacture of pressure vessel plates. During the welding process, the higher values of hardness and simultaneously decreasing of plasticity was ob-served and measured in the heat affected zone. Therefore, there was necessary to preheat the base material, or to apply the heat treatment after welding, or to suggest any combination of both mentioned ways. First of all, the groups of tested plates with required parameters were chosen for the application of the submerged arc welding method (according to ČSN EN ISO 4063), and preparation of samples for hardness measurement (ČSN EN ISO 6507) as the next step. The main goal of this experiment was to determine the hardness level for two fine grained steel grades after welding with the given parameters, as well as to adjust or to eliminiate the heat treatment pr
Název v anglickém jazyce
Influence of preheating and heat treatment after welding according to the EN 13445 and ASME Code on the hardness level of welded joints for the Pressure Vessel Plates
Popis výsledku anglicky
The paper deals with an analysis of preheating and heat treatment after welding and their influence on the final hardness level in case of welded jonits for common materials applied for manufacture of pressure vessel plates. During the welding process, the higher values of hardness and simultaneously decreasing of plasticity was ob-served and measured in the heat affected zone. Therefore, there was necessary to preheat the base material, or to apply the heat treatment after welding, or to suggest any combination of both mentioned ways. First of all, the groups of tested plates with required parameters were chosen for the application of the submerged arc welding method (according to ČSN EN ISO 4063), and preparation of samples for hardness measurement (ČSN EN ISO 6507) as the next step. The main goal of this experiment was to determine the hardness level for two fine grained steel grades after welding with the given parameters, as well as to adjust or to eliminiate the heat treatment pr
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JG - Hutnictví, kovové materiály
OECD FORD obor
—
Návaznosti výsledku
Projekt
<a href="/cs/project/LO1207" target="_blank" >LO1207: Podpora udržitelnosti Inovačního centra diagnostiky a aplikace materiálů na ČVUT-FS v Praze</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2014
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Manufacturing Technology
ISSN
1213-2489
e-ISSN
—
Svazek periodika
14
Číslo periodika v rámci svazku
12
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
6
Strana od-do
511-516
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—