Study of differences between results from laboratory tests and testS of real tools for selected cold work tool steels

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21220%2F19%3A00375229" target="_blank" >RIV/68407700:21220/19:00375229 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.4028/www.scientific.net/DDF.395.113" target="_blank" >http://dx.doi.org/10.4028/www.scientific.net/DDF.395.113</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/DDF.395.113" target="_blank" >10.4028/www.scientific.net/DDF.395.113</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Study of differences between results from laboratory tests and testS of real tools for selected cold work tool steels

Popis výsledku v původním jazyce

The growing pressure on tool performance and durability increases demands on the materials used and on the choice of optimal heat treatment. The properties of tool steels produced by conventional and powder metallurgy (1.2379, Vanadis 23) were compared after different heat treatment modes. Cryogenic treatment was performed in several batches for 4 hours at -90°C or -196°C. Cryogenic treatment was inserted between quenching and tempering. Mechanical properties were evaluated by hardness tests and three-point bending strength and wear resistance by Pin-on-disk tests. Metallographic analysis was performed using light and electron microscopy. On the basis of the results obtained both materials were subject to selected heat treatment and experimental forming tools produced which were used in operation. During operation the wear of the tools (shape change and volume loss) was assessed. Results of the laboratory tests were then compared with operation tests.

Název v anglickém jazyce

Study of differences between results from laboratory tests and testS of real tools for selected cold work tool steels

Popis výsledku anglicky

The growing pressure on tool performance and durability increases demands on the materials used and on the choice of optimal heat treatment. The properties of tool steels produced by conventional and powder metallurgy (1.2379, Vanadis 23) were compared after different heat treatment modes. Cryogenic treatment was performed in several batches for 4 hours at -90°C or -196°C. Cryogenic treatment was inserted between quenching and tempering. Mechanical properties were evaluated by hardness tests and three-point bending strength and wear resistance by Pin-on-disk tests. Metallographic analysis was performed using light and electron microscopy. On the basis of the results obtained both materials were subject to selected heat treatment and experimental forming tools produced which were used in operation. During operation the wear of the tools (shape change and volume loss) was assessed. Results of the laboratory tests were then compared with operation tests.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/LO1207" target="_blank" >LO1207: Podpora udržitelnosti Inovačního centra diagnostiky a aplikace materiálů na ČVUT-FS v Praze</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Defect and Diffusion Forum

ISBN

—

ISSN

1012-0386

e-ISSN

1662-9507

Počet stran výsledku

11

Strana od-do

113-123

Název nakladatele

Scientific.net

Místo vydání

Durnten-Zurich

Místo konání akce

Hotel Alexandra, Púchov

Datum konání akce

20. 11. 2018

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—