Experimental investigation of CMT discontinuous wire arc additive manufacturing of Inconel 625

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21220%2F22%3A00359213" target="_blank" >RIV/68407700:21220/22:00359213 - isvavai.cz</a>

Výsledek na webu

<a href="https://doi.org/10.1007/s00170-022-09878-7" target="_blank" >https://doi.org/10.1007/s00170-022-09878-7</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/s00170-022-09878-7" target="_blank" >10.1007/s00170-022-09878-7</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Experimental investigation of CMT discontinuous wire arc additive manufacturing of Inconel 625

Popis výsledku v původním jazyce

Additive manufacturing (AM) is a progressive technology which holds promise for manufacturing of heat resistant super alloys. One of the most productive methods is wire arc additive manufacturing (WAAM). In this article, an alternative WAAM strategy is investigated. Experimental clads and material tests were performed to evaluate the material properties obtained through a cold metal transfer (CMT) discontinuous WAAM of Inconel 625 alloy. Using the modern terminology of Fronius Gmbh this method is called CMT cycle step. The difference is that it is automatically controlled by the welding source. CMT discontinuous WAAM has lower productivity and a higher consumption of shielding gas. However, it excels in low heat input and precise material cladding in comparison with a standard CMT continuous WAAM. It enables fabrication of finer details even on thin-walled components or in sections with problematic heat dissipation. Samples manufactured using this strategy were also compared with samples manufactured through a standard CMT continuous WAAM. Two sets of manufactured samples were thus tested. The following material tests were performed: (i) metallographic analysis, (ii) x-ray tomography, (iii) SEM analysis, (iv) hardness, (v) tensile strength (20 °C, 650 °C) and (vi) pin-on-disc (20 °C, 650 °C). The results show that the CMT discontinuous WAAM led to improved material properties in the Inconel 625 samples. Ultimate tensile strength improved by 15% at 20 °C and by 4% at 650 °C. Wear resistance at 650 °C was about two times higher. This paper concludes that the CMT discontinuous WAAM for Inconel 625 is definitely suitable for manufacturing of complex shapes, fine details and thin-walled components.

Název v anglickém jazyce

Experimental investigation of CMT discontinuous wire arc additive manufacturing of Inconel 625

Popis výsledku anglicky

Additive manufacturing (AM) is a progressive technology which holds promise for manufacturing of heat resistant super alloys. One of the most productive methods is wire arc additive manufacturing (WAAM). In this article, an alternative WAAM strategy is investigated. Experimental clads and material tests were performed to evaluate the material properties obtained through a cold metal transfer (CMT) discontinuous WAAM of Inconel 625 alloy. Using the modern terminology of Fronius Gmbh this method is called CMT cycle step. The difference is that it is automatically controlled by the welding source. CMT discontinuous WAAM has lower productivity and a higher consumption of shielding gas. However, it excels in low heat input and precise material cladding in comparison with a standard CMT continuous WAAM. It enables fabrication of finer details even on thin-walled components or in sections with problematic heat dissipation. Samples manufactured using this strategy were also compared with samples manufactured through a standard CMT continuous WAAM. Two sets of manufactured samples were thus tested. The following material tests were performed: (i) metallographic analysis, (ii) x-ray tomography, (iii) SEM analysis, (iv) hardness, (v) tensile strength (20 °C, 650 °C) and (vi) pin-on-disc (20 °C, 650 °C). The results show that the CMT discontinuous WAAM led to improved material properties in the Inconel 625 samples. Ultimate tensile strength improved by 15% at 20 °C and by 4% at 650 °C. Wear resistance at 650 °C was about two times higher. This paper concludes that the CMT discontinuous WAAM for Inconel 625 is definitely suitable for manufacturing of complex shapes, fine details and thin-walled components.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/EF16_019%2F0000826" target="_blank" >EF16_019/0000826: Centrum pokročilých leteckých technologií</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2022

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

The International Journal of Advanced Manufacturing Technology

ISSN

0268-3768

e-ISSN

1433-3015

Svazek periodika

122

Číslo periodika v rámci svazku

2

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

17

Strana od-do

711-727

Kód UT WoS článku

000840626600001

EID výsledku v databázi Scopus

2-s2.0-85136920490