Solar and Wireless Energy Harvesting Semi-active UHF RFID Tag Design and Prototyping

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21230%2F14%3A00222483" target="_blank" >RIV/68407700:21230/14:00222483 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.1109/MECHATRONIKA.2014.7018257" target="_blank" >http://dx.doi.org/10.1109/MECHATRONIKA.2014.7018257</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1109/MECHATRONIKA.2014.7018257" target="_blank" >10.1109/MECHATRONIKA.2014.7018257</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Solar and Wireless Energy Harvesting Semi-active UHF RFID Tag Design and Prototyping

Popis výsledku v původním jazyce

In this paper we describe the main phases of an ideation, hardware design, development, prototyping and testing of UHF RFID high memory capacity TAG supported with two external independent power sources. There were used current best practices to design and build a proof of concept with two energy sources: Solar and Wireless which made the TAG battery free and semi-active. Harvested energy should help to support RFID semi-active tag whenever radio signal or light is available. Based on the parallel experience, existing research of similar projects and requirements there was decided to create our own PCB layout for tag board carrying two modules. First source is Solar panel; second one is a Wireless power receiver at frequency of 915MHz. Concerning the RFID circuit Monza Dura family chip as the main microprocessor for RFID transponder was used and a printed PCB antenna as per vendor specification to allow it to interact with remote RFID transmitter. All the system is printed on a FR4 sub

Název v anglickém jazyce

Solar and Wireless Energy Harvesting Semi-active UHF RFID Tag Design and Prototyping

Popis výsledku anglicky

In this paper we describe the main phases of an ideation, hardware design, development, prototyping and testing of UHF RFID high memory capacity TAG supported with two external independent power sources. There were used current best practices to design and build a proof of concept with two energy sources: Solar and Wireless which made the TAG battery free and semi-active. Harvested energy should help to support RFID semi-active tag whenever radio signal or light is available. Based on the parallel experience, existing research of similar projects and requirements there was decided to create our own PCB layout for tag board carrying two modules. First source is Solar panel; second one is a Wireless power receiver at frequency of 915MHz. Concerning the RFID circuit Monza Dura family chip as the main microprocessor for RFID transponder was used and a printed PCB antenna as per vendor specification to allow it to interact with remote RFID transmitter. All the system is printed on a FR4 sub

Druh

D - Stať ve sborníku

CEP obor

JA - Elektronika a optoelektronika, elektrotechnika

OECD FORD obor

—

Projekt

<a href="/cs/project/LF13005" target="_blank" >LF13005: RFID technologie v logistických sítích automobilového průmyslu</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2014

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

16th Mechatronika 2014

ISBN

978-80-214-4816-2

ISSN

—

e-ISSN

—

Počet stran výsledku

6

Strana od-do

188-193

Název nakladatele

Brno University of Technology

Místo vydání

Brno

Místo konání akce

Brno

Datum konání akce

3. 12. 2014

Typ akce podle státní příslušnosti

EUR - Evropská akce

Kód UT WoS článku

—