Single-tone and Polyharmonic Eddy Current Metal Detection and Non-Destructive Testing Education Software

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21230%2F16%3A00305618" target="_blank" >RIV/68407700:21230/16:00305618 - isvavai.cz</a>

Výsledek na webu

<a href="http://iopscience.iop.org/article/10.1088/1742-6596/772/1/012052/meta" target="_blank" >http://iopscience.iop.org/article/10.1088/1742-6596/772/1/012052/meta</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1088/1742-6596/772/1/012052" target="_blank" >10.1088/1742-6596/772/1/012052</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Single-tone and Polyharmonic Eddy Current Metal Detection and Non-Destructive Testing Education Software

Popis výsledku v původním jazyce

This paper describes the design of a measuring chain for polyharmonic metal detectors used for education in laboratory exercises at Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Measurement. The Measuring chain is composed of DDS signal generator, Digitiser and PC with software programmed in Labview. Eddy current principles or more specifically eddy current metal detectors are an important part of nondestructive testing, instrumentations and measurement. A short introduction to the background and principles of eddy current metal detectors are presented. Next part of the article deals with a brief description of the most common methods, as well as, non-traditional polyharmonic methods for eddy current metal detection. The following part contains an implementation of the proposed algorithms in LabVIEW graphical programming language. Finally, the created program for education of eddy current metal detectors and results obtained on the metal detector ATMID are discussed.

Název v anglickém jazyce

Single-tone and Polyharmonic Eddy Current Metal Detection and Non-Destructive Testing Education Software

Popis výsledku anglicky

This paper describes the design of a measuring chain for polyharmonic metal detectors used for education in laboratory exercises at Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Measurement. The Measuring chain is composed of DDS signal generator, Digitiser and PC with software programmed in Labview. Eddy current principles or more specifically eddy current metal detectors are an important part of nondestructive testing, instrumentations and measurement. A short introduction to the background and principles of eddy current metal detectors are presented. Next part of the article deals with a brief description of the most common methods, as well as, non-traditional polyharmonic methods for eddy current metal detection. The following part contains an implementation of the proposed algorithms in LabVIEW graphical programming language. Finally, the created program for education of eddy current metal detectors and results obtained on the metal detector ATMID are discussed.

Druh

D - Stať ve sborníku

CEP obor

JB - Senzory, čidla, měření a regulace

OECD FORD obor

—

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2016

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Journal of Physics: Conference Series

ISBN

—

ISSN

1742-6588

e-ISSN

—

Počet stran výsledku

6

Strana od-do

—

Název nakladatele

Institute of Physics Publishing

Místo vydání

Bristol

Místo konání akce

University of California, Berkeley

Datum konání akce

3. 8. 2016

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—