Simulation and fabrication of 3D printed optical planar multimode 1x2Y splitters

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21230%2F19%3A00335240" target="_blank" >RIV/68407700:21230/19:00335240 - isvavai.cz</a>

Výsledek na webu

<a href="http://hdl.handle.net/10467/87134" target="_blank" >http://hdl.handle.net/10467/87134</a>

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Simulation and fabrication of 3D printed optical planar multimode 1x2Y splitters

Popis výsledku v původním jazyce

This paper reports about design and simulation of planar optical multimodal splitters in combination with plastic optical fibers for the visible spectrum. These devices consisted of Veroclear RGD810 core and Polydimethylsiloxane PDMS substrate/cladding. The splitters were simulated by the beam propagation method using RSoft software and by using a ray tracing method used OptiCAD software. The simulations were done for the width of waveguide core 750 µm. The core was manufactured by 3D printer Stratasys Objet 30 Pro. Estimation of total excess loss was discussed using waveguide loss theory. Material constants were measured. Both - extrinsic and intrinsic factors were defined and used for this estimation. And the final model is presented. The values of optical insertion loss were simulated at 650 nm and compared to values measured.

Název v anglickém jazyce

Simulation and fabrication of 3D printed optical planar multimode 1x2Y splitters

Popis výsledku anglicky

This paper reports about design and simulation of planar optical multimodal splitters in combination with plastic optical fibers for the visible spectrum. These devices consisted of Veroclear RGD810 core and Polydimethylsiloxane PDMS substrate/cladding. The splitters were simulated by the beam propagation method using RSoft software and by using a ray tracing method used OptiCAD software. The simulations were done for the width of waveguide core 750 µm. The core was manufactured by 3D printer Stratasys Objet 30 Pro. Estimation of total excess loss was discussed using waveguide loss theory. Material constants were measured. Both - extrinsic and intrinsic factors were defined and used for this estimation. And the final model is presented. The values of optical insertion loss were simulated at 650 nm and compared to values measured.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/EF16_019%2F0000778" target="_blank" >EF16_019/0000778: Centrum pokročilých aplikovaných přírodních věd</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Proceedings of Adept

ISBN

978-80-554-1568-0

ISSN

—

e-ISSN

—

Počet stran výsledku

4

Strana od-do

159-162

Název nakladatele

EDIS - Publishing Institution of the University of Zilina

Místo vydání

Žilina

Místo konání akce

Štrbské Pleso

Datum konání akce

24. 6. 2019

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—