Residual Stress Surface Distribution in the Vicinity of Welds in Laser Welded Steel Sheets

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21340%2F13%3A00214489" target="_blank" >RIV/68407700:21340/13:00214489 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Residual Stress Surface Distribution in the Vicinity of Welds in Laser Welded Steel Sheets

Popis výsledku v původním jazyce

Advent of high power diode laser has substantially contributed to the popularity of laser welding in industry where its virtues such as low heat input and good weld strength are highly appreciated. However, one of the drawbacks of the laser welding is distortion of the welded bodies that is closely linked with the generation and/or redistribution of residual stresses in the vicinity of the weld. In this contribution, mapping of surface macroscopic residual stresses in two directions, i.e. parallel and perpendicular to the welds, were performed for two bodies. The first contained a weld created with the high power diode laser beam speed of 2 m/min and the second with the speed of 15 m/min. Our aim was to compare not only resulting fields of residual stresses, but also to perform qualitative assessment of the possible presence of crystallographic texture and gain a qualitative apprehension about the grain sizes in the vicinity of a laser weld joining two steel sheets. Larger distortion o

Název v anglickém jazyce

Residual Stress Surface Distribution in the Vicinity of Welds in Laser Welded Steel Sheets

Popis výsledku anglicky

Advent of high power diode laser has substantially contributed to the popularity of laser welding in industry where its virtues such as low heat input and good weld strength are highly appreciated. However, one of the drawbacks of the laser welding is distortion of the welded bodies that is closely linked with the generation and/or redistribution of residual stresses in the vicinity of the weld. In this contribution, mapping of surface macroscopic residual stresses in two directions, i.e. parallel and perpendicular to the welds, were performed for two bodies. The first contained a weld created with the high power diode laser beam speed of 2 m/min and the second with the speed of 15 m/min. Our aim was to compare not only resulting fields of residual stresses, but also to perform qualitative assessment of the possible presence of crystallographic texture and gain a qualitative apprehension about the grain sizes in the vicinity of a laser weld joining two steel sheets. Larger distortion o

Druh

D - Stať ve sborníku

CEP obor

JG - Hutnictví, kovové materiály

OECD FORD obor

—

Projekt

<a href="/cs/project/TA02011004" target="_blank" >TA02011004: Aplikace laserových technologií v dopravní technice</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2013

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Proceedings of the 51st Conference on Experimental Stress Analysis

ISBN

978-80-7414-579-7

ISSN

—

e-ISSN

—

Počet stran výsledku

6

Strana od-do

—

Název nakladatele

FVTM,UJEP

Místo vydání

Ústí nad Labem

Místo konání akce

Litoměřice

Datum konání akce

11. 6. 2013

Typ akce podle státní příslušnosti

EUR - Evropská akce

Kód UT WoS článku

—