Use of relocation device at scanning of polymeric material surface quality

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28110%2F14%3A43873142" target="_blank" >RIV/70883521:28110/14:43873142 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.4028/www.scientific.net/AMM.693.243" target="_blank" >http://dx.doi.org/10.4028/www.scientific.net/AMM.693.243</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/AMM.693.243" target="_blank" >10.4028/www.scientific.net/AMM.693.243</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Use of relocation device at scanning of polymeric material surface quality

Popis výsledku v původním jazyce

Nowadays, manufacturers and users of parts made of polymeric materials make increasing demands on surface quality of these parts. In order to fulfill these claims, it is necessary to use not only the quality measurement systems for surface quality inspection, but also suitable products that allow to set up the inspected polymeric component properly set up to the measuring system scanner. However, it is not sufficient. Due to the requirements of the customers or the production it is often necessary to repeat the surface quality measurement, which is more and more often done in 3D; that might be quite difficult. Except for special cases there should not be any marks done by the inspection workplace which might lower the inspected surface quality. Therefore it is not suitable to make mechanical marks such as scratch, ridge, etc. On the other hand, other types of marks done by non-invasive method, such as sticking paper marks, measuring cross, etc. is also not admissible as there might res

Název v anglickém jazyce

Use of relocation device at scanning of polymeric material surface quality

Popis výsledku anglicky

Nowadays, manufacturers and users of parts made of polymeric materials make increasing demands on surface quality of these parts. In order to fulfill these claims, it is necessary to use not only the quality measurement systems for surface quality inspection, but also suitable products that allow to set up the inspected polymeric component properly set up to the measuring system scanner. However, it is not sufficient. Due to the requirements of the customers or the production it is often necessary to repeat the surface quality measurement, which is more and more often done in 3D; that might be quite difficult. Except for special cases there should not be any marks done by the inspection workplace which might lower the inspected surface quality. Therefore it is not suitable to make mechanical marks such as scratch, ridge, etc. On the other hand, other types of marks done by non-invasive method, such as sticking paper marks, measuring cross, etc. is also not admissible as there might res

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JP - Průmyslové procesy a zpracování

OECD FORD obor

—

Projekt

—

Návaznosti

V - Vyzkumna aktivita podporovana z jinych verejnych zdroju

Rok uplatnění

2014

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Applied Mechanics and Materials

ISSN

1660-9336

e-ISSN

—

Svazek periodika

693

Číslo periodika v rámci svazku

Neuveden

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

4

Strana od-do

243-246

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—