Use of Irradiated Polymers after Their Lifetime Period
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28110%2F18%3A63519657" target="_blank" >RIV/70883521:28110/18:63519657 - isvavai.cz</a>
Nalezeny alternativní kódy
RIV/70883521:28140/18:63519657
Výsledek na webu
<a href="https://www.mdpi.com/2073-4360/10/6/641/htm" target="_blank" >https://www.mdpi.com/2073-4360/10/6/641/htm</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.3390/polym10060641" target="_blank" >10.3390/polym10060641</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Use of Irradiated Polymers after Their Lifetime Period
Popis výsledku v původním jazyce
This article deals with the study of the utilisation of irradiated HDPE products after their end-of-life cycle. Today, polymer waste processing is a matter of evermore intensive discussion. Common thermoplastic waste recycling-especially in the case of wastes with a defined composition-is generally well-known-and frequently used. On the contrary, processing cross-linked plastics is impossible to do in the same way as with virgin thermoplastics-mainly due to the impossibility of remelting them. The possibility of using waste in the form of grit or a powder, made from cross-linked High Density PolyEthylene (rHDPEx) products, after their end-of-life cycle, as a filler for virgin Low Density PolyEthylene (LDPE) was tested in a matrix. It was found that both the mechanical behaviour and processability of new composites with an LDPE matrix, with rHDPEx as a filler, depend-to a high degree-on the amount of the filler. The composite can be processed up to 60% of the filler content. The Polymer Mixture Fluidity dropped significantly, in line with the amount of filler, while the mechanical properties, on the other hand, predominantly grew with the increasing amount of rHDPEx.
Název v anglickém jazyce
Use of Irradiated Polymers after Their Lifetime Period
Popis výsledku anglicky
This article deals with the study of the utilisation of irradiated HDPE products after their end-of-life cycle. Today, polymer waste processing is a matter of evermore intensive discussion. Common thermoplastic waste recycling-especially in the case of wastes with a defined composition-is generally well-known-and frequently used. On the contrary, processing cross-linked plastics is impossible to do in the same way as with virgin thermoplastics-mainly due to the impossibility of remelting them. The possibility of using waste in the form of grit or a powder, made from cross-linked High Density PolyEthylene (rHDPEx) products, after their end-of-life cycle, as a filler for virgin Low Density PolyEthylene (LDPE) was tested in a matrix. It was found that both the mechanical behaviour and processability of new composites with an LDPE matrix, with rHDPEx as a filler, depend-to a high degree-on the amount of the filler. The composite can be processed up to 60% of the filler content. The Polymer Mixture Fluidity dropped significantly, in line with the amount of filler, while the mechanical properties, on the other hand, predominantly grew with the increasing amount of rHDPEx.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20501 - Materials engineering
Návaznosti výsledku
Projekt
Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2018
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Polymers
ISSN
2073-4360
e-ISSN
—
Svazek periodika
10
Číslo periodika v rámci svazku
6
Stát vydavatele periodika
CH - Švýcarská konfederace
Počet stran výsledku
16
Strana od-do
"nestrankovano"
Kód UT WoS článku
000436560200078
EID výsledku v databázi Scopus
2-s2.0-85048400606