The effect of polymer pin ribs on reinforcement of sandwich structures
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28110%2F18%3A63521087" target="_blank" >RIV/70883521:28110/18:63521087 - isvavai.cz</a>
Nalezeny alternativní kódy
RIV/70883521:28610/18:63521087
Výsledek na webu
<a href="http://dx.doi.org/10.21062/ujep/196.2018/a/1213-2489/mt/18/6/889" target="_blank" >http://dx.doi.org/10.21062/ujep/196.2018/a/1213-2489/mt/18/6/889</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.21062/ujep/196.2018/a/1213-2489/mt/18/6/889" target="_blank" >10.21062/ujep/196.2018/a/1213-2489/mt/18/6/889</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
The effect of polymer pin ribs on reinforcement of sandwich structures
Popis výsledku v původním jazyce
This research paper deals with an influence of reinforcing polymer ribs on selected mechanical properties of sandwich structures. Reinforcing epoxy ribs are produced directly by the vacuum infusion technology when resin during its flow fills the prepared holes in the polymer core. In the experiment, two rib sizes (diameters) were tested as well as two variants of hole patterns on the core surface. The possible influence of the core material was evaluated on two core material types with different thicknesses. In addition to the observed mechanical properties observed, the types of failure and changes of the sandwich panels weight were also characterized. The obtained results show a significant increase in flexural strength and stiffness of all types and shapes of prepared reinforcing polymer ribs. Positive effect was also observed in the case of edgewise compression load capacity.
Název v anglickém jazyce
The effect of polymer pin ribs on reinforcement of sandwich structures
Popis výsledku anglicky
This research paper deals with an influence of reinforcing polymer ribs on selected mechanical properties of sandwich structures. Reinforcing epoxy ribs are produced directly by the vacuum infusion technology when resin during its flow fills the prepared holes in the polymer core. In the experiment, two rib sizes (diameters) were tested as well as two variants of hole patterns on the core surface. The possible influence of the core material was evaluated on two core material types with different thicknesses. In addition to the observed mechanical properties observed, the types of failure and changes of the sandwich panels weight were also characterized. The obtained results show a significant increase in flexural strength and stiffness of all types and shapes of prepared reinforcing polymer ribs. Positive effect was also observed in the case of edgewise compression load capacity.
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
10404 - Polymer science
Návaznosti výsledku
Projekt
Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2018
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Manufacturing Technology
ISSN
1213-2489
e-ISSN
—
Svazek periodika
18
Číslo periodika v rámci svazku
6
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
6
Strana od-do
889-894
Kód UT WoS článku
—
EID výsledku v databázi Scopus
2-s2.0-85059331365