Influence of molecular weight, temperature, and extensional rheology on melt blowing process stability for linear isotactic polypropylene

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28110%2F20%3A63526187" target="_blank" >RIV/70883521:28110/20:63526187 - isvavai.cz</a>

Výsledek na webu

<a href="https://aip.scitation.org/doi/abs/10.1063/5.0020773?journalCode=phf" target="_blank" >https://aip.scitation.org/doi/abs/10.1063/5.0020773?journalCode=phf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1063/5.0020773" target="_blank" >10.1063/5.0020773</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of molecular weight, temperature, and extensional rheology on melt blowing process stability for linear isotactic polypropylene

Popis výsledku v původním jazyce

In this work, three linear isotactic polypropylenes with different weight-average molecular weights, M-w, and comparable polydispersities were used to produce nonwovens by melt blowing technology at two different temperatures, T. The air/polymer flow rate was changed to maintain the same average fiber diameter, resulting in a different broadness of fiber diameter distribution, which was quantified by the coefficient of variation, CV. The elasticity of the material was evaluated by the reptation-mode relaxation time, lambda(1), and the Rouse-mode reorientation time, lambda(2), determined from the deformation rate dependent shear viscosity data. Extensional rheology was evaluated using uniaxial extensional viscosity measured over a very wide range of strain rates (2 x 10(4) s(-1)-2 x 10(6) s(-1)) using entrance pressure drop and Gibson methods. An obtained plateau value of uniaxial extensional viscosity at the highest extensional strain rates, eta(E,infinity) (normalized by the three times zero-shear rate viscosity, eta(0)), and the minimum uniaxial extensional viscosity, eta(E,min), were related to M-w and T using simple equations. It has been found that the stability of fiber production captured by CV depends exclusively on the extensional properties of the polypropylene melts, namely, eta(E,U,)infinity/3 eta(0) and eta(E,U,min). These findings are important especially with regard to the stable production of polymeric nanofibers by melt blowing technology.

Název v anglickém jazyce

Influence of molecular weight, temperature, and extensional rheology on melt blowing process stability for linear isotactic polypropylene

Popis výsledku anglicky

In this work, three linear isotactic polypropylenes with different weight-average molecular weights, M-w, and comparable polydispersities were used to produce nonwovens by melt blowing technology at two different temperatures, T. The air/polymer flow rate was changed to maintain the same average fiber diameter, resulting in a different broadness of fiber diameter distribution, which was quantified by the coefficient of variation, CV. The elasticity of the material was evaluated by the reptation-mode relaxation time, lambda(1), and the Rouse-mode reorientation time, lambda(2), determined from the deformation rate dependent shear viscosity data. Extensional rheology was evaluated using uniaxial extensional viscosity measured over a very wide range of strain rates (2 x 10(4) s(-1)-2 x 10(6) s(-1)) using entrance pressure drop and Gibson methods. An obtained plateau value of uniaxial extensional viscosity at the highest extensional strain rates, eta(E,infinity) (normalized by the three times zero-shear rate viscosity, eta(0)), and the minimum uniaxial extensional viscosity, eta(E,min), were related to M-w and T using simple equations. It has been found that the stability of fiber production captured by CV depends exclusively on the extensional properties of the polypropylene melts, namely, eta(E,U,)infinity/3 eta(0) and eta(E,U,min). These findings are important especially with regard to the stable production of polymeric nanofibers by melt blowing technology.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

10404 - Polymer science

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Physics of Fluids

ISSN

1070-6631

e-ISSN

—

Svazek periodika

32

Číslo periodika v rámci svazku

8

Stát vydavatele periodika

US - Spojené státy americké

Počet stran výsledku

17

Strana od-do

"083110-1"-"083110-16"

Kód UT WoS článku

000565260200002

EID výsledku v databázi Scopus

2-s2.0-85092221567