Microhardness and elastic modulus of thin coatings applied via PVD and CVD techniques

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28110%2F25%3A63596058" target="_blank" >RIV/70883521:28110/25:63596058 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mmscience.eu/journal/issues/june-2025/articles" target="_blank" >https://www.mmscience.eu/journal/issues/june-2025/articles</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.17973/MMSJ.2025_06_2025031" target="_blank" >10.17973/MMSJ.2025_06_2025031</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Microhardness and elastic modulus of thin coatings applied via PVD and CVD techniques

Popis výsledku v původním jazyce

This study investigates the microhardness and mechanical properties of thin coatings applied to cemented carbide cutting tools. Two primary coating techniques were examined: Physical Vapor Deposition (PVD) and Moderate Temperature Chemical Vapor Deposition (MT-CVD). PVD coatings of titanium carbonitride (TiCN) and aluminium titanium nitride (AlTiN) were applied, along with multi-layer CVD coatings consisting of TiCN, titanium carbide (TiC), and aluminium oxide (Al ₂ O₃ ). Depth-sensing indentation (DSI) tests using a Vickers indenter were conducted to determine the microhardness and elastic modulus of the coatings. The Oliver and Pharr method, was employed to analyse load-unload curves, enabling precise evaluation without direct measurement of imprint areas. The results demonstrated that TiCN coatings applied via PVD exhibited the highest microhardness as a complex is 2857 HVIT and elastic modulus among all tested samples is 649 GPa. This superior performance indicates enhanced wear resistance and mechanical stability, which are critical for extending the lifespan and efficiency of cutting tools. While multi-layer CVD coatings also offered benefits, their overall performance was inferior to that of TiCN PVD coatings.

Název v anglickém jazyce

Microhardness and elastic modulus of thin coatings applied via PVD and CVD techniques

Popis výsledku anglicky

This study investigates the microhardness and mechanical properties of thin coatings applied to cemented carbide cutting tools. Two primary coating techniques were examined: Physical Vapor Deposition (PVD) and Moderate Temperature Chemical Vapor Deposition (MT-CVD). PVD coatings of titanium carbonitride (TiCN) and aluminium titanium nitride (AlTiN) were applied, along with multi-layer CVD coatings consisting of TiCN, titanium carbide (TiC), and aluminium oxide (Al ₂ O₃ ). Depth-sensing indentation (DSI) tests using a Vickers indenter were conducted to determine the microhardness and elastic modulus of the coatings. The Oliver and Pharr method, was employed to analyse load-unload curves, enabling precise evaluation without direct measurement of imprint areas. The results demonstrated that TiCN coatings applied via PVD exhibited the highest microhardness as a complex is 2857 HVIT and elastic modulus among all tested samples is 649 GPa. This superior performance indicates enhanced wear resistance and mechanical stability, which are critical for extending the lifespan and efficiency of cutting tools. While multi-layer CVD coatings also offered benefits, their overall performance was inferior to that of TiCN PVD coatings.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

V - Vyzkumna aktivita podporovana z jinych verejnych zdroju

Rok uplatnění

2025

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

MM Science Journal

ISSN

1803-1269

e-ISSN

1805-0476

Svazek periodika

2025

Číslo periodika v rámci svazku

Neuveden

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

9

Strana od-do

8322-8330

Kód UT WoS článku

001500453100001

EID výsledku v databázi Scopus

2-s2.0-105007724297