Recyclation of Irradiated HDPE - Influence on Impact Toughness

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28140%2F13%3A43869955" target="_blank" >RIV/70883521:28140/13:43869955 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/70883521:28110/13:43869955

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Recyclation of Irradiated HDPE - Influence on Impact Toughness

Popis výsledku v původním jazyce

Little research was done to investigate possible utilization of the irradiated materials after the end of their lifetime despite the growing potential of modification by irradiation. This research paper deals with usage of this recycled material as filler into non -recycled one. A powder of recycled irradiated high -density polyethylene was used as filler into non - irradiated powder or granules of low - density polyethylene. Two types of compounds were prepared ? each with the same concentrations. These were from 0 % to 60 %. NotchedCharpy impact test was performed at ambient conditions and influence of this filler was tested. Two parameters were observed ? Maximum Force (force needed for breakage of the material) and Impact Toughness (describing impact behavior of the material). Measured results show minimum influence on Maximum Force ? it varied around 280 N. Results of Impact Toughness are much more consistent because all two compounds show similar tre nd. In all cases was this tre

Název v anglickém jazyce

Recyclation of Irradiated HDPE - Influence on Impact Toughness

Popis výsledku anglicky

Little research was done to investigate possible utilization of the irradiated materials after the end of their lifetime despite the growing potential of modification by irradiation. This research paper deals with usage of this recycled material as filler into non -recycled one. A powder of recycled irradiated high -density polyethylene was used as filler into non - irradiated powder or granules of low - density polyethylene. Two types of compounds were prepared ? each with the same concentrations. These were from 0 % to 60 %. NotchedCharpy impact test was performed at ambient conditions and influence of this filler was tested. Two parameters were observed ? Maximum Force (force needed for breakage of the material) and Impact Toughness (describing impact behavior of the material). Measured results show minimum influence on Maximum Force ? it varied around 280 N. Results of Impact Toughness are much more consistent because all two compounds show similar tre nd. In all cases was this tre

Druh

D - Stať ve sborníku

CEP obor

JP - Průmyslové procesy a zpracování

OECD FORD obor

—

Projekt

<a href="/cs/project/ED2.1.00%2F03.0089" target="_blank" >ED2.1.00/03.0089: Centrum bezpečnostních, informačních a pokročilých technologií (CEBIA-Tech)</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2013

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Recent, Advances in Automatic Control, Information and Communications 14th International Conference on Automation and Information (ICAI´13) 13th International Conference on Applied Informatics and Communications (AIC´13)

ISBN

978-960-474-316-2

ISSN

1790-5117

e-ISSN

—

Počet stran výsledku

4

Strana od-do

111-114

Název nakladatele

WSEAS World Science and Engineering Academy and Science

Místo vydání

Atény

Místo konání akce

Valencie

Datum konání akce

6. 8. 2013

Typ akce podle státní příslušnosti

EUR - Evropská akce

Kód UT WoS článku

—