Influence of fall height on high impact polystyrene deformation and characteristics of drop weight test

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28140%2F17%3A63517091" target="_blank" >RIV/70883521:28140/17:63517091 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.matec-conferences.org/articles/matecconf/pdf/2017/39/matecconf_cscc2017_02051.pdf" target="_blank" >https://www.matec-conferences.org/articles/matecconf/pdf/2017/39/matecconf_cscc2017_02051.pdf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1051/matecconf/201712502051" target="_blank" >10.1051/matecconf/201712502051</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of fall height on high impact polystyrene deformation and characteristics of drop weight test

Popis výsledku v původním jazyce

This study deals with high impact polystyrene (HIPS) which was subjected the drop-weight test. HIPS is a polymer produced by the reaction between butadiene synthetic elastomer and styrene (5-14 %) which contains the crystal polymer in certain amounts and is commonly used in mechanical engineering applications where machine parts are exposed to impact loading. The injection moulded HIPS samples were subjected the penetration test at different fall heights and the results were subsequently evaluated and discussed. It was found out that all fall heights are suitable for HIPS penetration, but the optimal one is 50 J because of the smallest variation range. Higher heights are not needed because of increasing power consumption of the test device. From the results, it is clear, that HIPS is not so highly impact resistant material as for example HDPE, because of that is this material suitable for applications where is not often exposed to too big impacts at high velocities.

Název v anglickém jazyce

Influence of fall height on high impact polystyrene deformation and characteristics of drop weight test

Popis výsledku anglicky

This study deals with high impact polystyrene (HIPS) which was subjected the drop-weight test. HIPS is a polymer produced by the reaction between butadiene synthetic elastomer and styrene (5-14 %) which contains the crystal polymer in certain amounts and is commonly used in mechanical engineering applications where machine parts are exposed to impact loading. The injection moulded HIPS samples were subjected the penetration test at different fall heights and the results were subsequently evaluated and discussed. It was found out that all fall heights are suitable for HIPS penetration, but the optimal one is 50 J because of the smallest variation range. Higher heights are not needed because of increasing power consumption of the test device. From the results, it is clear, that HIPS is not so highly impact resistant material as for example HDPE, because of that is this material suitable for applications where is not often exposed to too big impacts at high velocities.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

MATEC Web of Conferences

ISBN

—

ISSN

2261-236X

e-ISSN

neuvedeno

Počet stran výsledku

4

Strana od-do

"nestrankovano"

Název nakladatele

EDP Sciences

Místo vydání

Les Ulis

Místo konání akce

Heraklion, Crete

Datum konání akce

14. 7. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—