Surface modification of metallic inserts for enhancing adhesion at the metal–polymer interface

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28610%2F21%3A63542578" target="_blank" >RIV/70883521:28610/21:63542578 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/70883521:28110/21:63542578

Výsledek na webu

<a href="https://www.mdpi.com/2073-4360/13/22/4015" target="_blank" >https://www.mdpi.com/2073-4360/13/22/4015</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/polym13224015" target="_blank" >10.3390/polym13224015</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Surface modification of metallic inserts for enhancing adhesion at the metal–polymer interface

Popis výsledku v původním jazyce

A combination of mechanical and chemical treatments was utilized to modify the surface textures of copper and duralumin inserts in order to enhance the adhesion at the metal–polymer interface and provide an adhesive joint with a high loadbearing capacity. Pretreatment of the surfaces with sandblasting was followed by etching with various chemical mixtures. The resulting surface textures were evaluated with a scanning electron microscope (SEM) and an optical confocal microscope. Surface geometry parameters (Sa, Sz, and Sdr) were measured and their relationships to the adhesion joint strength were studied. It was found that the virgin and purely mechanically treated inserts resulted in joints with poor loadbearing capacity, while a hundredfold (duralumin) and ninetyfold (copper) increase in the force to break was observed for some combinations of mechanical and chemical treatments. It was determined that the critical factor is overcoming a certain surface roughness threshold with the mechanical pretreatment to maximize the potential of the mechanical/chemical approach for the particular combination of material and etchant.

Název v anglickém jazyce

Surface modification of metallic inserts for enhancing adhesion at the metal–polymer interface

Popis výsledku anglicky

A combination of mechanical and chemical treatments was utilized to modify the surface textures of copper and duralumin inserts in order to enhance the adhesion at the metal–polymer interface and provide an adhesive joint with a high loadbearing capacity. Pretreatment of the surfaces with sandblasting was followed by etching with various chemical mixtures. The resulting surface textures were evaluated with a scanning electron microscope (SEM) and an optical confocal microscope. Surface geometry parameters (Sa, Sz, and Sdr) were measured and their relationships to the adhesion joint strength were studied. It was found that the virgin and purely mechanically treated inserts resulted in joints with poor loadbearing capacity, while a hundredfold (duralumin) and ninetyfold (copper) increase in the force to break was observed for some combinations of mechanical and chemical treatments. It was determined that the critical factor is overcoming a certain surface roughness threshold with the mechanical pretreatment to maximize the potential of the mechanical/chemical approach for the particular combination of material and etchant.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

10404 - Polymer science

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2021

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Polymers

ISSN

2073-4360

e-ISSN

—

Svazek periodika

13

Číslo periodika v rámci svazku

22

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

13

Strana od-do

—

Kód UT WoS článku

000723684500001

EID výsledku v databázi Scopus

2-s2.0-85119719112