Influence of 3D Printing Topology by DMLS Method on Crack Propagation

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F71226401%3A_____%2F21%3AN0100595" target="_blank" >RIV/71226401:_____/21:N0100595 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mdpi.com/1996-1944/14/23/7483" target="_blank" >https://www.mdpi.com/1996-1944/14/23/7483</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma14237483" target="_blank" >10.3390/ma14237483</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of 3D Printing Topology by DMLS Method on Crack Propagation

Popis výsledku v původním jazyce

The presented text deals with research into the influence of the printing layers’ orientation on crack propagation in an AlSi10Mg material specimen, produced by additive technology, using the Direct Metal Laser Sintering (DMLS) method. It is a method based on sintering and melting layers of powder material using a laser beam. The material specimen is presented as a Compact Tension test specimen and is printed in four different defined orientations (topology) of the printing layers—0°, 45°, 90°, and twice 90°. The normalized specimen is loaded cyclically, where the crack length is measured and recorded, and at the same time, the crack growth rate is determined. The evaluation of the experiment shows an apparent influence of the topology, which is essential especially for possible use in the design and technical preparation of the production of real machine parts in industrial practice. Simultaneously with the measurement results, other influencing factors are listed, especially product postprocessing and the measurement method used. The hypothesis of crack propagation using Computer Aided Engineering/Finite Element Method (CAE/FEM) simulation is also stated here based on the achieved results.

Název v anglickém jazyce

Influence of 3D Printing Topology by DMLS Method on Crack Propagation

Popis výsledku anglicky

The presented text deals with research into the influence of the printing layers’ orientation on crack propagation in an AlSi10Mg material specimen, produced by additive technology, using the Direct Metal Laser Sintering (DMLS) method. It is a method based on sintering and melting layers of powder material using a laser beam. The material specimen is presented as a Compact Tension test specimen and is printed in four different defined orientations (topology) of the printing layers—0°, 45°, 90°, and twice 90°. The normalized specimen is loaded cyclically, where the crack length is measured and recorded, and at the same time, the crack growth rate is determined. The evaluation of the experiment shows an apparent influence of the topology, which is essential especially for possible use in the design and technical preparation of the production of real machine parts in industrial practice. Simultaneously with the measurement results, other influencing factors are listed, especially product postprocessing and the measurement method used. The hypothesis of crack propagation using Computer Aided Engineering/Finite Element Method (CAE/FEM) simulation is also stated here based on the achieved results.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2021

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials

ISSN

1996-1944

e-ISSN

1996-1944

Svazek periodika

14

Číslo periodika v rámci svazku

23

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

14

Strana od-do

7483

Kód UT WoS článku

000735693400001

EID výsledku v databázi Scopus

2-s2.0-85120831927