Research and Evaluation of the Influence of the Construction of the Gate and the Influence of the Piston Velocity on the Distribution of Gases into the Volume of the Casting

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F75081431%3A_____%2F21%3A00002058" target="_blank" >RIV/75081431:_____/21:00002058 - isvavai.cz</a>

Výsledek na webu

<a href="https://apps.webofknowledge.com/full_record.do?product=WOS&search_mode=GeneralSearch&qid=1&SID=F3ex42oZ6e8KsuYcpHj&page=1&doc=1" target="_blank" >https://apps.webofknowledge.com/full_record.do?product=WOS&search_mode=GeneralSearch&qid=1&SID=F3ex42oZ6e8KsuYcpHj&page=1&doc=1</a>

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Research and Evaluation of the Influence of the Construction of the Gate and the Influence of the Piston Velocity on the Distribution of Gases into the Volume of the Casting

Popis výsledku v původním jazyce

Distribution of gasses to the cast volume and volume of pores can be maintained within the acceptable limits by means of correct setting of technological parameters of casting and by selection of suitable structure and gating system arrangement. The main idea of this paper solves the issue of suitability of die casting adjustment-i.e., change of technological parameters or change of structural solution of the gating system-with regards to inner soundness of casts produced in die casting process. Parameters which were compared included height of a gate and velocity of a piston. The melt velocity in the gate was used as a correlating factor between the gate height and piston velocity. The evaluated parameter was gas entrapment in the cast at the end of the filling phase of die casting cycle and at the same time percentage of porosity in the samples taken from the main runner. On the basis of the performed experiments it was proved that the change of technological parameters, particularly of pressing velocity of the piston, directly influences distribution of gasses to the cast volume.

Název v anglickém jazyce

Research and Evaluation of the Influence of the Construction of the Gate and the Influence of the Piston Velocity on the Distribution of Gases into the Volume of the Casting

Popis výsledku anglicky

Distribution of gasses to the cast volume and volume of pores can be maintained within the acceptable limits by means of correct setting of technological parameters of casting and by selection of suitable structure and gating system arrangement. The main idea of this paper solves the issue of suitability of die casting adjustment-i.e., change of technological parameters or change of structural solution of the gating system-with regards to inner soundness of casts produced in die casting process. Parameters which were compared included height of a gate and velocity of a piston. The melt velocity in the gate was used as a correlating factor between the gate height and piston velocity. The evaluated parameter was gas entrapment in the cast at the end of the filling phase of die casting cycle and at the same time percentage of porosity in the samples taken from the main runner. On the basis of the performed experiments it was proved that the change of technological parameters, particularly of pressing velocity of the piston, directly influences distribution of gasses to the cast volume.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20100 - Civil engineering

Projekt

—

Návaznosti

V - Vyzkumna aktivita podporovana z jinych verejnych zdroju

Rok uplatnění

2021

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

MATERIALS

ISSN

1996-1944

e-ISSN

—

Svazek periodika

14

Číslo periodika v rámci svazku

9

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

16

Strana od-do

1-16

Kód UT WoS článku

000650558200001

EID výsledku v databázi Scopus

—