On the Application of the PVD Hard Coatings for Ball Milling of Shaped Surfaces
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F10%3APU96432" target="_blank" >RIV/00216305:26210/10:PU96432 - isvavai.cz</a>
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
On the Application of the PVD Hard Coatings for Ball Milling of Shaped Surfaces
Popis výsledku v původním jazyce
Force load analysis is a usual procedure of current cutting tool testing in not only ball end milling but in general machining. This paper is aimed to force load analysis of the cutting tool when the HSS ball end milling is performed onto an alumina alloy. A variation of the cutting tool force loading has been observed when a tilt of the tool was set perpendicularly to the direction of the feed speed vector in the range 0-20deg and cutting conditions were kept constant. In the first part of the study, some uncoated HSS ball milling tools have been used to exclude an influence of PVD coating and its disperse in quality. In the second part of the project the PVD coatings on the base of (TixAl1-x)N and TiB2 have been successively applied. However, the main objective of the research was to quantify other cutting phenomena also, like the chip formation, roughness of the machined surface as they present a key role in the complex surface machining for moulds.
Název v anglickém jazyce
On the Application of the PVD Hard Coatings for Ball Milling of Shaped Surfaces
Popis výsledku anglicky
Force load analysis is a usual procedure of current cutting tool testing in not only ball end milling but in general machining. This paper is aimed to force load analysis of the cutting tool when the HSS ball end milling is performed onto an alumina alloy. A variation of the cutting tool force loading has been observed when a tilt of the tool was set perpendicularly to the direction of the feed speed vector in the range 0-20deg and cutting conditions were kept constant. In the first part of the study, some uncoated HSS ball milling tools have been used to exclude an influence of PVD coating and its disperse in quality. In the second part of the project the PVD coatings on the base of (TixAl1-x)N and TiB2 have been successively applied. However, the main objective of the research was to quantify other cutting phenomena also, like the chip formation, roughness of the machined surface as they present a key role in the complex surface machining for moulds.
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JQ - Strojní zařízení a nástroje
OECD FORD obor
—
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2010
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Internet Journal of Engineering and Technology
ISSN
1338-2357
e-ISSN
—
Svazek periodika
1
Číslo periodika v rámci svazku
1
Stát vydavatele periodika
SK - Slovenská republika
Počet stran výsledku
8
Strana od-do
11-18
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—