QUALITY OF DIMENSIONS ACCURANCY OF COMPONENTS AFTER WEDM DEPENDING ON THE HEAT TREATMENT
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F15%3APU115234" target="_blank" >RIV/00216305:26210/15:PU115234 - isvavai.cz</a>
Výsledek na webu
<a href="http://dx.doi.org/10.17973/MMSJ.2015_12_201563" target="_blank" >http://dx.doi.org/10.17973/MMSJ.2015_12_201563</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.17973/MMSJ.2015_12_201563" target="_blank" >10.17973/MMSJ.2015_12_201563</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
QUALITY OF DIMENSIONS ACCURANCY OF COMPONENTS AFTER WEDM DEPENDING ON THE HEAT TREATMENT
Popis výsledku v původním jazyce
The main purpose of this paper is to examine the gap width of the wire cut after WEDM depending on the heat treatment of machined material - high-alloy steel X210Cr12. This steel is usually used for the production of cutting tools. Cutting gap occurs during the discharge between the tool electrode and the machined material. This discharge causes melting of microscopic particles of the workpiece; the particles are then washed out from the place of the discharge by dielectric, which creates small craters. The size of the cutting gap is a limiting factor for the manufacture of internal radius and also it affects the final dimensions of the machined part. The heat treatment has an effect on the grain size and hardness of the material which results in a huge evaporation of the material and its subsequent leaching from the cutting place. The amount of evaporated and leached material was examined on the groove with width of 3 mm produced by WEDM to 4 differently heat treated steel samples X210Cr12. For cutting of all grooves the same parameters of the machine settings were used. The grooves were cut into four sections in order to achieve the highest possible dimensional accuracy.
Název v anglickém jazyce
QUALITY OF DIMENSIONS ACCURANCY OF COMPONENTS AFTER WEDM DEPENDING ON THE HEAT TREATMENT
Popis výsledku anglicky
The main purpose of this paper is to examine the gap width of the wire cut after WEDM depending on the heat treatment of machined material - high-alloy steel X210Cr12. This steel is usually used for the production of cutting tools. Cutting gap occurs during the discharge between the tool electrode and the machined material. This discharge causes melting of microscopic particles of the workpiece; the particles are then washed out from the place of the discharge by dielectric, which creates small craters. The size of the cutting gap is a limiting factor for the manufacture of internal radius and also it affects the final dimensions of the machined part. The heat treatment has an effect on the grain size and hardness of the material which results in a huge evaporation of the material and its subsequent leaching from the cutting place. The amount of evaporated and leached material was examined on the groove with width of 3 mm produced by WEDM to 4 differently heat treated steel samples X210Cr12. For cutting of all grooves the same parameters of the machine settings were used. The grooves were cut into four sections in order to achieve the highest possible dimensional accuracy.
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
<a href="/cs/project/LO1202" target="_blank" >LO1202: NETME CENTRE PLUS</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2015
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
MM Science Journal
ISSN
1803-1269
e-ISSN
1805-0476
Svazek periodika
2015
Číslo periodika v rámci svazku
4
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
4
Strana od-do
790-793
Kód UT WoS článku
—
EID výsledku v databázi Scopus
2-s2.0-84949510302