Experimental analysis on machinability of aluminium alloy using WEDM technology

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F15%3APU115290" target="_blank" >RIV/00216305:26210/15:PU115290 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.17973/MMSJ.2015_12_201549" target="_blank" >http://dx.doi.org/10.17973/MMSJ.2015_12_201549</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.17973/MMSJ.2015_12_201549" target="_blank" >10.17973/MMSJ.2015_12_201549</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Experimental analysis on machinability of aluminium alloy using WEDM technology

Popis výsledku v původním jazyce

Wire electrical discharge machining (WEDM) is unconventional method commonly used for manufacturing of components with difficult shapes or profiles. It is very useful for machining very small – micro components with high dimensional accuracy and quality of surface finish. This technology allows even cutting of very hard materials (such as Aluminium alloys), provided they are conductive. First part of this paper deals with machining aluminium alloy AlZn6Mg2Cu, setting of cutting parameters and measuring properties such as surface roughness and cutting width (kerf) of the machined samples. The second part is focused on studying of machining process using design of experiments (DOE) methods and analysis of variance (ANOVA), especially for identifying of key parameters that have influence on the WEDM process. The aim of this work is to explore the possibility, whether if by performing planned experiment and subsequent evaluation in the future allows determining exactly setting the key parameters influencing the process of WEDM.

Název v anglickém jazyce

Experimental analysis on machinability of aluminium alloy using WEDM technology

Popis výsledku anglicky

Wire electrical discharge machining (WEDM) is unconventional method commonly used for manufacturing of components with difficult shapes or profiles. It is very useful for machining very small – micro components with high dimensional accuracy and quality of surface finish. This technology allows even cutting of very hard materials (such as Aluminium alloys), provided they are conductive. First part of this paper deals with machining aluminium alloy AlZn6Mg2Cu, setting of cutting parameters and measuring properties such as surface roughness and cutting width (kerf) of the machined samples. The second part is focused on studying of machining process using design of experiments (DOE) methods and analysis of variance (ANOVA), especially for identifying of key parameters that have influence on the WEDM process. The aim of this work is to explore the possibility, whether if by performing planned experiment and subsequent evaluation in the future allows determining exactly setting the key parameters influencing the process of WEDM.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/LO1202" target="_blank" >LO1202: NETME CENTRE PLUS</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2015

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

MM Science Journal

ISSN

1803-1269

e-ISSN

1805-0476

Svazek periodika

2015

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

6

Strana od-do

722-727

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-84949523180