Influence of mesh density on calculated extreme stresses in aortic aneurysms

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F16%3APU122007" target="_blank" >RIV/00216305:26210/16:PU122007 - isvavai.cz</a>

Výsledek na webu

<a href="http://www.kme.zcu.cz/acm/acm/issue/view/20" target="_blank" >http://www.kme.zcu.cz/acm/acm/issue/view/20</a>

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of mesh density on calculated extreme stresses in aortic aneurysms

Popis výsledku v původním jazyce

The paper deals with evaluation of the influence of finite element mesh density on the resulting extreme stresses in models of abdominal aortic aneurysms. In most patient-specific computational models published recently, a free mesh of tetrahedrons is used and any information on density of the applied mesh is often missing. In this study a comparison of different mesh densities has been realized with four patient-specific model geometries, all based on a numerical reconstruction of the unloaded geometry of the aneurysm, and with two different Yeoh-type constitutive models. It has been shown that resulting maximum stresses are not mesh independent; due to a better description of the stress gradient in the critical location, the maximum wall stress increases with increasing number of elements throughout the wall thickness, especially in models without residual stresses. This effect is more pronounced when using Vande Geest constitutive model with higher strain stiffening than for Raghavan-Vorp material parameters. Although the mesh density requirements were not so high when the stress gradient was reduced by taking residual stresses into consideration, even in this case low numbers of elements throughout the wall thickness may give mesh dependent results. Although for a rigorous recommendation of the mesh density more analyses are needed, it was shown that the time consuming procedure of taking residual stresses into consideration cannot be replaced by a simpler model with rough mesh.

Název v anglickém jazyce

Influence of mesh density on calculated extreme stresses in aortic aneurysms

Popis výsledku anglicky

The paper deals with evaluation of the influence of finite element mesh density on the resulting extreme stresses in models of abdominal aortic aneurysms. In most patient-specific computational models published recently, a free mesh of tetrahedrons is used and any information on density of the applied mesh is often missing. In this study a comparison of different mesh densities has been realized with four patient-specific model geometries, all based on a numerical reconstruction of the unloaded geometry of the aneurysm, and with two different Yeoh-type constitutive models. It has been shown that resulting maximum stresses are not mesh independent; due to a better description of the stress gradient in the critical location, the maximum wall stress increases with increasing number of elements throughout the wall thickness, especially in models without residual stresses. This effect is more pronounced when using Vande Geest constitutive model with higher strain stiffening than for Raghavan-Vorp material parameters. Although the mesh density requirements were not so high when the stress gradient was reduced by taking residual stresses into consideration, even in this case low numbers of elements throughout the wall thickness may give mesh dependent results. Although for a rigorous recommendation of the mesh density more analyses are needed, it was shown that the time consuming procedure of taking residual stresses into consideration cannot be replaced by a simpler model with rough mesh.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

10610 - Biophysics

Projekt

<a href="/cs/project/LO1202" target="_blank" >LO1202: NETME CENTRE PLUS</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2016

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Applied andComputational Mechanics

ISSN

1802-680X

e-ISSN

2336-1182

Svazek periodika

10

Číslo periodika v rámci svazku

2

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

14

Strana od-do

97-110

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85010952073