Optimalization of WEDM settings parameters when machining pure aluminium using DoE

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F17%3APU124508" target="_blank" >RIV/00216305:26210/17:PU124508 - isvavai.cz</a>

Výsledek na webu

<a href="http://www.mmscience.eu/content/file/archives/MM_Science_201795.pdf" target="_blank" >http://www.mmscience.eu/content/file/archives/MM_Science_201795.pdf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.17973/MMSJ.2017_12_201795" target="_blank" >10.17973/MMSJ.2017_12_201795</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Optimalization of WEDM settings parameters when machining pure aluminium using DoE

Popis výsledku v původním jazyce

The unconventional wire electric discharge machining technology (WEDM) is widely used in many industries, which is why thereis a permanent emphasis on increasing the quality of such machined surface. The aim of this studywas to carry out a design of experiment (DoE) to reduce the surface qualityparameterPq. During the 33-round experiment, the input factors – machine setting parameters, such as gap voltage, pulse on time, pulse off time, wire speed, and dischargecurrent, werechanged. Subsequently, Pq – rootmean square deviation of the primary profile and Pa – arithmetic average of the primary profile were evaluated on the machined surfaces of pure aluminium. By using DoE, the setting of the machine’ sparameters was designed in order to achieve the highest possible surface quality.

Název v anglickém jazyce

Optimalization of WEDM settings parameters when machining pure aluminium using DoE

Popis výsledku anglicky

The unconventional wire electric discharge machining technology (WEDM) is widely used in many industries, which is why thereis a permanent emphasis on increasing the quality of such machined surface. The aim of this studywas to carry out a design of experiment (DoE) to reduce the surface qualityparameterPq. During the 33-round experiment, the input factors – machine setting parameters, such as gap voltage, pulse on time, pulse off time, wire speed, and dischargecurrent, werechanged. Subsequently, Pq – rootmean square deviation of the primary profile and Pa – arithmetic average of the primary profile were evaluated on the machined surfaces of pure aluminium. By using DoE, the setting of the machine’ sparameters was designed in order to achieve the highest possible surface quality.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/LO1202" target="_blank" >LO1202: NETME CENTRE PLUS</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

MM Science Journal

ISSN

1803-1269

e-ISSN

1805-0476

Svazek periodika

2017

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

4

Strana od-do

2105-2108

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85038124074