The New Stepper Driver for Low-Cost Arduino Based 3D Printer with Dynamic Stepper Control

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26220%2F17%3APU124449" target="_blank" >RIV/00216305:26220/17:PU124449 - isvavai.cz</a>

Výsledek na webu

<a href="https://link.springer.com/chapter/10.1007/978-3-319-65960-2_57" target="_blank" >https://link.springer.com/chapter/10.1007/978-3-319-65960-2_57</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/978-3-319-65960-2_57" target="_blank" >10.1007/978-3-319-65960-2_57</a>

Jazyk výsledku

angličtina

Název v původním jazyce

The New Stepper Driver for Low-Cost Arduino Based 3D Printer with Dynamic Stepper Control

Popis výsledku v původním jazyce

The article deals with design of a new stepper driver for axis control of Arduino based 3D printer. The driver was designed because of the ineligible conception of mostly used ones plug and play modules based on A4988 or similar and because there is still a gap in open source drivers available on the marker. It is based on integrated stepper driver with much higher power and in much better mechanical conception. Also, a big emphasis was placed on the PCB design, which is proved in final testing comparing quality of power chips supply. In combination with innovated control system, this driver allows using Dynamic Stepper Control ability, which allows affecting stepper motor parameters like phase cur-rent and micro-stepping level in real time on demand by control software.

Název v anglickém jazyce

The New Stepper Driver for Low-Cost Arduino Based 3D Printer with Dynamic Stepper Control

Popis výsledku anglicky

The article deals with design of a new stepper driver for axis control of Arduino based 3D printer. The driver was designed because of the ineligible conception of mostly used ones plug and play modules based on A4988 or similar and because there is still a gap in open source drivers available on the marker. It is based on integrated stepper driver with much higher power and in much better mechanical conception. Also, a big emphasis was placed on the PCB design, which is proved in final testing comparing quality of power chips supply. In combination with innovated control system, this driver allows using Dynamic Stepper Control ability, which allows affecting stepper motor parameters like phase cur-rent and micro-stepping level in real time on demand by control software.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20201 - Electrical and electronic engineering

Projekt

<a href="/cs/project/LO1210" target="_blank" >LO1210: Energie v podmínkách udržitelného rozvoje (EN-PUR)</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Mechatronics 2017

ISBN

978-3-319-65959-6

ISSN

2194-5357

e-ISSN

—

Počet stran výsledku

9

Strana od-do

458-466

Název nakladatele

Springer International Publishing AG 2018

Místo vydání

Cham

Místo konání akce

Brno

Datum konání akce

6. 9. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

000554435500057