3D Printed Nanocarbon Frameworks for Li-Ion Battery Cathodes

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26620%2F21%3APU140772" target="_blank" >RIV/00216305:26620/21:PU140772 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/62156489:43210/21:43919155

Výsledek na webu

<a href="https://onlinelibrary.wiley.com/doi/10.1002/adfm.202007285" target="_blank" >https://onlinelibrary.wiley.com/doi/10.1002/adfm.202007285</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1002/adfm.202007285" target="_blank" >10.1002/adfm.202007285</a>

Jazyk výsledku

angličtina

Název v původním jazyce

3D Printed Nanocarbon Frameworks for Li-Ion Battery Cathodes

Popis výsledku v původním jazyce

The use of conductive carbon materials in 3D-printing is attracting growing academic and industrial attention in electrochemical energy storage due to the high customization and on-demand capabilities of the additive manufacturing. However, typical polymers used in conductive filaments for 3D printing show high resistivity and low compatibility with electrochemical energy applications. Removal of insulating thermoplastics in as-printed materials is a common post-printing strategy, however, excessive loss of thermoplastics can weaken the structural integrity. This work reports a two-step surface engineering methodology for fabrication of 3D-printed carbon materials for electrochemical applications, incorporating conductive poly(ortho-phenylenediamine) (PoPD) via electrodeposition. A conductive PoPD effectively enhances the electrochemical activities of 3D-printed frameworks. When PoPD-refilled frameworks casted with LiMn2O4 (LMO) composite materials used as battery cathode, it delivers a capacity of 69.1 mAh g(-1) at a current density of 0.036 mA cm(-2) (approximate to 1.2 C discharge rate) and good cyclability with a retained capacity of 84.4% after 200 cycles at 0.36 mA cm(-2). This work provides a pathway for developing electroactive 3D-printed electrodes particularly with cost-efficient low-dimensional carbon materials for aqueous rechargeable Li-ion batteries.

Název v anglickém jazyce

3D Printed Nanocarbon Frameworks for Li-Ion Battery Cathodes

Popis výsledku anglicky

The use of conductive carbon materials in 3D-printing is attracting growing academic and industrial attention in electrochemical energy storage due to the high customization and on-demand capabilities of the additive manufacturing. However, typical polymers used in conductive filaments for 3D printing show high resistivity and low compatibility with electrochemical energy applications. Removal of insulating thermoplastics in as-printed materials is a common post-printing strategy, however, excessive loss of thermoplastics can weaken the structural integrity. This work reports a two-step surface engineering methodology for fabrication of 3D-printed carbon materials for electrochemical applications, incorporating conductive poly(ortho-phenylenediamine) (PoPD) via electrodeposition. A conductive PoPD effectively enhances the electrochemical activities of 3D-printed frameworks. When PoPD-refilled frameworks casted with LiMn2O4 (LMO) composite materials used as battery cathode, it delivers a capacity of 69.1 mAh g(-1) at a current density of 0.036 mA cm(-2) (approximate to 1.2 C discharge rate) and good cyclability with a retained capacity of 84.4% after 200 cycles at 0.36 mA cm(-2). This work provides a pathway for developing electroactive 3D-printed electrodes particularly with cost-efficient low-dimensional carbon materials for aqueous rechargeable Li-ion batteries.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

10405 - Electrochemistry (dry cells, batteries, fuel cells, corrosion metals, electrolysis)

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2021

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

ADVANCED FUNCTIONAL MATERIALS

ISSN

1616-301X

e-ISSN

1616-3028

Svazek periodika

31

Číslo periodika v rámci svazku

11

Stát vydavatele periodika

DE - Spolková republika Německo

Počet stran výsledku

10

Strana od-do

„2007285-1“-„2007285-10“

Kód UT WoS článku

000607632700001

EID výsledku v databázi Scopus

—