Influence of Aluminum on the Wear Properties of High-Carbon Metastable Austenitic Steels
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F26316919%3A_____%2F22%3AN0000036" target="_blank" >RIV/26316919:_____/22:N0000036 - isvavai.cz</a>
Výsledek na webu
<a href="https://onlinelibrary.wiley.com/doi/epdf/10.1002/srin.202200545" target="_blank" >https://onlinelibrary.wiley.com/doi/epdf/10.1002/srin.202200545</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1002/srin.202200545" target="_blank" >10.1002/srin.202200545</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Influence of Aluminum on the Wear Properties of High-Carbon Metastable Austenitic Steels
Popis výsledku v původním jazyce
The two-body abrasive wear properties of metastable austenitic steels (MAS) against SiC abrasive paper are investigated at different wear loads. To ensure a metastable austenitic microstructure, the alloying compositions are chosen such that the martensite start temperature of the MAS is approximately at room temperature, while the proportions of carbon, manganese, and aluminum change. The abrasion test results are compared to martensitic (40MnB5) and austenitic steel (Hadfield steel). An up to four times lower weight loss is found for the MAS compared to the Hadfield steel and up to 6.7 times lower weight loss compared to the martensitic steel. It is found that the wear resistance of the MAS increases significantly with wear load. Wear resistance of over 1300 Nm mm-3 is achieved at the highest wear load of 32 N. The wear properties of the MAS are associated with an increase in the surface hardness resulting from a mechanically induced austenite to martensite phase transformation. It is shown that the addition of aluminum to the MAS reduces the wear resistance. This is explained by an increase in stacking fault energy and the associated restriction of the mechanically induced transformation to martensite.
Název v anglickém jazyce
Influence of Aluminum on the Wear Properties of High-Carbon Metastable Austenitic Steels
Popis výsledku anglicky
The two-body abrasive wear properties of metastable austenitic steels (MAS) against SiC abrasive paper are investigated at different wear loads. To ensure a metastable austenitic microstructure, the alloying compositions are chosen such that the martensite start temperature of the MAS is approximately at room temperature, while the proportions of carbon, manganese, and aluminum change. The abrasion test results are compared to martensitic (40MnB5) and austenitic steel (Hadfield steel). An up to four times lower weight loss is found for the MAS compared to the Hadfield steel and up to 6.7 times lower weight loss compared to the martensitic steel. It is found that the wear resistance of the MAS increases significantly with wear load. Wear resistance of over 1300 Nm mm-3 is achieved at the highest wear load of 32 N. The wear properties of the MAS are associated with an increase in the surface hardness resulting from a mechanically induced austenite to martensite phase transformation. It is shown that the addition of aluminum to the MAS reduces the wear resistance. This is explained by an increase in stacking fault energy and the associated restriction of the mechanically induced transformation to martensite.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20501 - Materials engineering
Návaznosti výsledku
Projekt
—
Návaznosti
I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace
Ostatní
Rok uplatnění
2022
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
STEEL RESEARCH INTERNATIONAL
ISSN
1611-3683
e-ISSN
1869-344X
Svazek periodika
94
Číslo periodika v rámci svazku
1
Stát vydavatele periodika
DE - Spolková republika Německo
Počet stran výsledku
12
Strana od-do
nestránkováno
Kód UT WoS článku
000854885100001
EID výsledku v databázi Scopus
2-s2.0-85138212829