The effect of changes in feed rate on surface integrity during nickel coating grinding

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F44555601%3A13420%2F17%3A43893239" target="_blank" >RIV/44555601:13420/17:43893239 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.4028/www.scientific.net/SSP.261.207" target="_blank" >http://dx.doi.org/10.4028/www.scientific.net/SSP.261.207</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/SSP.261.207" target="_blank" >10.4028/www.scientific.net/SSP.261.207</a>

Jazyk výsledku

angličtina

Název v původním jazyce

The effect of changes in feed rate on surface integrity during nickel coating grinding

Popis výsledku v původním jazyce

Grinding is an important and very frequently used technology, allowing for significant gains in surface integrity. Products which have undergone surface treatment are often used in engineering. The required surface quality after grinding is one of the most important parameters. Nickel coatings as protection against corrosion are used, erosion, abrasion and as a material for the renovation of worn-out parts. This paper discusses the change of cutting conditions when samples were ground. The surface of the samples was treated with galvanically applied nickel. The data shows what level of surface roughness is achieved when choosing different cutting conditions. The results were evaluated on the basis of a comparison of the parameters of roughness. The input parameters were chosen on the basis of the practice, which was in the area carried out.

Název v anglickém jazyce

The effect of changes in feed rate on surface integrity during nickel coating grinding

Popis výsledku anglicky

Grinding is an important and very frequently used technology, allowing for significant gains in surface integrity. Products which have undergone surface treatment are often used in engineering. The required surface quality after grinding is one of the most important parameters. Nickel coatings as protection against corrosion are used, erosion, abrasion and as a material for the renovation of worn-out parts. This paper discusses the change of cutting conditions when samples were ground. The surface of the samples was treated with galvanically applied nickel. The data shows what level of surface roughness is achieved when choosing different cutting conditions. The results were evaluated on the basis of a comparison of the parameters of roughness. The input parameters were chosen on the basis of the practice, which was in the area carried out.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20300 - Mechanical engineering

Projekt

<a href="/cs/project/7AMB16AT039" target="_blank" >7AMB16AT039: Výzkum dosažení a hodnocení vysoké přesnosti obráběných povrchů</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Solid State Phenomena

ISBN

978-3-0357-1199-8

ISSN

—

e-ISSN

1662-9779

Počet stran výsledku

8

Strana od-do

207-214

Název nakladatele

Trans Tech Publications Ltd.

Místo vydání

Zurich

Místo konání akce

Řecko

Datum konání akce

6. 9. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—