Anisotropy Determination of Deep-drawing Sheet by means of Contact-less Optical System for Measuring Deformation

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F46747885%3A24210%2F11%3A%230002275" target="_blank" >RIV/46747885:24210/11:#0002275 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Anisotropy Determination of Deep-drawing Sheet by means of Contact-less Optical System for Measuring Deformation

Popis výsledku v původním jazyce

During last years there was a huge progress in contact-less systems for measuring deformation by means of photogrammetry which in its consequence leads to improve knowledge about material behavior under plastic deformation. This is mainly due to possibility e.g. to clearly identify important points during static tensile test like yield strength, ultimate strength or moment right before rupture and for each of these moments these systems immediately exhibit all important parameters from the metal formingpoint of view ? distribution of major and minor strains, Tresca or von Mises strain, strain rate and so on. Thus values which are sometimes really quite difficult to measure only by means of static tensile test. This paper describes possibility to determinate anisotropy of deep-drawing material by means of optical system ARAMIS ? v6.2.0-3 during whole evolution of static tensile test and comparison of results from those measured in values of deformation given by standard ČSN ISO 12 275.

Název v anglickém jazyce

Anisotropy Determination of Deep-drawing Sheet by means of Contact-less Optical System for Measuring Deformation

Popis výsledku anglicky

During last years there was a huge progress in contact-less systems for measuring deformation by means of photogrammetry which in its consequence leads to improve knowledge about material behavior under plastic deformation. This is mainly due to possibility e.g. to clearly identify important points during static tensile test like yield strength, ultimate strength or moment right before rupture and for each of these moments these systems immediately exhibit all important parameters from the metal formingpoint of view ? distribution of major and minor strains, Tresca or von Mises strain, strain rate and so on. Thus values which are sometimes really quite difficult to measure only by means of static tensile test. This paper describes possibility to determinate anisotropy of deep-drawing material by means of optical system ARAMIS ? v6.2.0-3 during whole evolution of static tensile test and comparison of results from those measured in values of deformation given by standard ČSN ISO 12 275.

Druh

D - Stať ve sborníku

CEP obor

JR - Ostatní strojírenství

OECD FORD obor

—

Projekt

<a href="/cs/project/GA101%2F09%2F1996" target="_blank" >GA101/09/1996: Vliv struktury materiálu na tvařitelnost slitin hliníku</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>Z - Vyzkumny zamer (s odkazem do CEZ)

Rok uplatnění

2011

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

METAL 2011 20th Anniversary International Conference on Metallurgy and Materials

ISBN

978-80-87294-24-6

ISSN

—

e-ISSN

—

Počet stran výsledku

6

Strana od-do

260-265

Název nakladatele

TANGER, Ltd., Keltickova 62, 710 00 Ostrava, Czech Republic, EU

Místo vydání

Ostrava

Místo konání akce

Brno

Datum konání akce

18. 5. 2011

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—