The use of metallography for examination of causes of surface defects on visual parts

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F46747885%3A24620%2F17%3A00004693" target="_blank" >RIV/46747885:24620/17:00004693 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.scientific.net/SSP.270.107" target="_blank" >https://www.scientific.net/SSP.270.107</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/SSP.270.107" target="_blank" >10.4028/www.scientific.net/SSP.270.107</a>

Jazyk výsledku

angličtina

Název v původním jazyce

The use of metallography for examination of causes of surface defects on visual parts

Popis výsledku v původním jazyce

Many of currently manufactured components intended for automotive, must not only meet the requirements on functionality, but also considerable demands on the visual appearance. Parts are subjected to thorough inspection and suppliers are forced to deal with causes of a very slight visual defects. When examining the defects, it is necessary to use a whole range of advanced analytical methods and procedures previously used only for identification of the physical and chemical properties and structure of the material. This paper deals with several examples which have been solved. It focuses especially on the use of demanding metallographic sample preparation from components with surface defects, examining the defects on the cross-section using mainly microscopic techniques and determining the causes of their generation. These results then serve as a basis for modification of the technology and thus they are the tool for significant reduction of amount of NOK parts.

Název v anglickém jazyce

The use of metallography for examination of causes of surface defects on visual parts

Popis výsledku anglicky

Many of currently manufactured components intended for automotive, must not only meet the requirements on functionality, but also considerable demands on the visual appearance. Parts are subjected to thorough inspection and suppliers are forced to deal with causes of a very slight visual defects. When examining the defects, it is necessary to use a whole range of advanced analytical methods and procedures previously used only for identification of the physical and chemical properties and structure of the material. This paper deals with several examples which have been solved. It focuses especially on the use of demanding metallographic sample preparation from components with surface defects, examining the defects on the cross-section using mainly microscopic techniques and determining the causes of their generation. These results then serve as a basis for modification of the technology and thus they are the tool for significant reduction of amount of NOK parts.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/LO1201" target="_blank" >LO1201: ROZVOJ ÚSTAVU PRO NANOMATERIÁLY, POKROČILÉ TECHNOLOGIE A INOVACE TECHNICKÉ UNIVERZITY V LIBERCI</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Solid State Phenomena

ISBN

978-303571241-4

ISSN

16629779

e-ISSN

—

Počet stran výsledku

5

Strana od-do

107-111

Název nakladatele

Trans Tech Publications

Místo vydání

—

Místo konání akce

Mariánské Lázně

Datum konání akce

1. 1. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—