Monitoring and Evaluating Cutting Tool Wear using a IFM G4 Microscope

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23210%2F16%3A43929637" target="_blank" >RIV/49777513:23210/16:43929637 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Monitoring and Evaluating Cutting Tool Wear using a IFM G4 Microscope

Popis výsledku v původním jazyce

Evaluation of the cutting tool wear is the general technic when the cutting tool life is monitored. On the base of the cutting conditions and machined material on the cutting edge surface the different tool wear type in-crease. On the base of the tool wear type and where the tool wear is created depend the evaluating parame-ters. All these parameters are describing by standards ISO 3685. When the standard optical microscope is used it is a very difficult to determine volume parameters and in many cases the actual (real) area of the tool wear. These standard optical microscope works on the base of the 2D screening. The new microscopes work on the base of the 3D scanning so, the user have full information about the surface. This article is focused on the evaluation of the volume parameters on the cutting edge generally on the size of BUE and on the for-mation of the groove. For the testing the different type of the cutting tools was used and for the monitoring and evaluation of the tool wear the IFM G4 microscope was used. These parameters are compared with the parameters which was measured on the 2D microscope.

Název v anglickém jazyce

Monitoring and Evaluating Cutting Tool Wear using a IFM G4 Microscope

Popis výsledku anglicky

Evaluation of the cutting tool wear is the general technic when the cutting tool life is monitored. On the base of the cutting conditions and machined material on the cutting edge surface the different tool wear type in-crease. On the base of the tool wear type and where the tool wear is created depend the evaluating parame-ters. All these parameters are describing by standards ISO 3685. When the standard optical microscope is used it is a very difficult to determine volume parameters and in many cases the actual (real) area of the tool wear. These standard optical microscope works on the base of the 2D screening. The new microscopes work on the base of the 3D scanning so, the user have full information about the surface. This article is focused on the evaluation of the volume parameters on the cutting edge generally on the size of BUE and on the for-mation of the groove. For the testing the different type of the cutting tools was used and for the monitoring and evaluation of the tool wear the IFM G4 microscope was used. These parameters are compared with the parameters which was measured on the 2D microscope.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JR - Ostatní strojírenství

OECD FORD obor

—

Projekt

<a href="/cs/project/LO1502" target="_blank" >LO1502: Rozvoj Regionálního technologického institutu</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2016

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

16

Číslo periodika v rámci svazku

5

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

6

Strana od-do

1211-1216

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—