Effects of Grinding Conditions and Strategy on the Quality of the Cutting Edge
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23210%2F18%3A43950897" target="_blank" >RIV/49777513:23210/18:43950897 - isvavai.cz</a>
Výsledek na webu
<a href="http://arl.ujep.cz/arl-ujep/en/csg/?repo=ujeprepo&key=72000420188" target="_blank" >http://arl.ujep.cz/arl-ujep/en/csg/?repo=ujeprepo&key=72000420188</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.21062/ujep/43.2018/a/1213-2489/MT/18/1/3" target="_blank" >10.21062/ujep/43.2018/a/1213-2489/MT/18/1/3</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Effects of Grinding Conditions and Strategy on the Quality of the Cutting Edge
Popis výsledku v původním jazyce
This article deals with the experimental grinding of cemented carbide cutting tools. Several carbide milling tools with the same geometry were ground under the different grinding conditions and strategy described in this research. The main aim is to determine the influence of the grinding process on the quality of the cutting edge. Different grinding conditions and strategies were used in grinding of the primary radial relief on the peripheral cutting edge. The cutting edge was analysed after grinding by an optical-scanning device and an electron micro-scope to determine the quality of the cutting edge and radial relief face of the tool. EDX analysis was used for the chemical characterization of the ground surface. The chipping of the cutting edge occurred when the grinding feed rate and the wheel spin direction was changed. The influence of the grinding conditions and strategy on the chipping formation was determined. The mean radius of the cutting edge after grinding was also measured. The results of this work will be used for further research and cutting experiments.
Název v anglickém jazyce
Effects of Grinding Conditions and Strategy on the Quality of the Cutting Edge
Popis výsledku anglicky
This article deals with the experimental grinding of cemented carbide cutting tools. Several carbide milling tools with the same geometry were ground under the different grinding conditions and strategy described in this research. The main aim is to determine the influence of the grinding process on the quality of the cutting edge. Different grinding conditions and strategies were used in grinding of the primary radial relief on the peripheral cutting edge. The cutting edge was analysed after grinding by an optical-scanning device and an electron micro-scope to determine the quality of the cutting edge and radial relief face of the tool. EDX analysis was used for the chemical characterization of the ground surface. The chipping of the cutting edge occurred when the grinding feed rate and the wheel spin direction was changed. The influence of the grinding conditions and strategy on the chipping formation was determined. The mean radius of the cutting edge after grinding was also measured. The results of this work will be used for further research and cutting experiments.
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
<a href="/cs/project/LO1502" target="_blank" >LO1502: Rozvoj Regionálního technologického institutu</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2018
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Manufacturing Technology
ISSN
1213-2489
e-ISSN
—
Svazek periodika
18
Číslo periodika v rámci svazku
1
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
5
Strana od-do
3-7
Kód UT WoS článku
—
EID výsledku v databázi Scopus
2-s2.0-85049605327