Influence of the Infill on the Tensile Strength and the Economic Factors of 3D Printing

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23210%2F19%3A43957366" target="_blank" >RIV/49777513:23210/19:43957366 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.daaam.info/Downloads/Pdfs/proceedings/proceedings_2019/147.pdf" target="_blank" >https://www.daaam.info/Downloads/Pdfs/proceedings/proceedings_2019/147.pdf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.2507/30th.daaam.proceedings.147" target="_blank" >10.2507/30th.daaam.proceedings.147</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of the Infill on the Tensile Strength and the Economic Factors of 3D Printing

Popis výsledku v původním jazyce

This work deals with the infill of 3D printed parts. The goal of this work is to provide recommendations on how much a part should be filled. The recommendation is supported by experiment. The selected load is tensile. Therefore, the geometry of the samples was based on the standard ČSN EN ISO 527-2. Five densities of infill were selected to determine an infill rate from 0 to 100%. In addition to the tensile strength values for each sample, the work also considers economic factors. Characteristic graphs for this issue were constructed at the end of the work. They give an overview of how tensile strength, as well as time, and the cost of 3D printing, change with increasing densities of infill.

Název v anglickém jazyce

Influence of the Infill on the Tensile Strength and the Economic Factors of 3D Printing

Popis výsledku anglicky

This work deals with the infill of 3D printed parts. The goal of this work is to provide recommendations on how much a part should be filled. The recommendation is supported by experiment. The selected load is tensile. Therefore, the geometry of the samples was based on the standard ČSN EN ISO 527-2. Five densities of infill were selected to determine an infill rate from 0 to 100%. In addition to the tensile strength values for each sample, the work also considers economic factors. Characteristic graphs for this issue were constructed at the end of the work. They give an overview of how tensile strength, as well as time, and the cost of 3D printing, change with increasing densities of infill.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/EF18_069%2F0010040" target="_blank" >EF18_069/0010040: Výzkum aditivních technologií pro budoucí uplatnění ve strojírenské praxi - RTI plus</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Proceedings of the 30th International DAAAM Symposium &quot;Intelligent Manufacturing &amp; Automation&quot;

ISBN

978-3-902734-22-8

ISSN

1726-9679

e-ISSN

—

Počet stran výsledku

5

Strana od-do

1056-1060

Název nakladatele

DAAAM International Vienna

Místo vydání

Vídeň

Místo konání akce

Zadar, Croatia EU

Datum konání akce

23. 10. 2019

Typ akce podle státní příslušnosti

EUR - Evropská akce

Kód UT WoS článku

—