Prediction of Cutting Parameters of HVOF-Sprayed Stellite 6

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23210%2F20%3A43958904" target="_blank" >RIV/49777513:23210/20:43958904 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mdpi.com/2076-3417/10/7/2524" target="_blank" >https://www.mdpi.com/2076-3417/10/7/2524</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/app10072524" target="_blank" >10.3390/app10072524</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Prediction of Cutting Parameters of HVOF-Sprayed Stellite 6

Popis výsledku v původním jazyce

In this research, the authors set out to propose a new method of predicting and adjusting the main cutting parameters of chip machining, namely spraying on the substrate. In the experiments, a total of 28 turning cuts on a Stellite 6 coating layer were realized. The base materials of the Stellite 6 layers were EN S235JRG1 and carbide WC-Co. This work aimed to find out and optimize the influence of di erent combinations of cutting parameters. Due to the coating solution, the work is focused on the evaluation of the roughness Ra (m) of the turned substrate, the grain size Dgr (m) of the spraying, the normal stress rz (MPa), the residual stress rez (MPa), the specific cutting force Fc (N), the quality of adhesion to the substrate Adhmp (MPa) and other parameters. For the sake of a comprehensive solution to the problem, several new predictive equations and subsequent suggestions for solutions have been derived from this research topic based on the newly obtained experimental results. The proposed models and procedures make it possible to get new results and insights into coating technologies.

Název v anglickém jazyce

Prediction of Cutting Parameters of HVOF-Sprayed Stellite 6

Popis výsledku anglicky

In this research, the authors set out to propose a new method of predicting and adjusting the main cutting parameters of chip machining, namely spraying on the substrate. In the experiments, a total of 28 turning cuts on a Stellite 6 coating layer were realized. The base materials of the Stellite 6 layers were EN S235JRG1 and carbide WC-Co. This work aimed to find out and optimize the influence of di erent combinations of cutting parameters. Due to the coating solution, the work is focused on the evaluation of the roughness Ra (m) of the turned substrate, the grain size Dgr (m) of the spraying, the normal stress rz (MPa), the residual stress rez (MPa), the specific cutting force Fc (N), the quality of adhesion to the substrate Adhmp (MPa) and other parameters. For the sake of a comprehensive solution to the problem, several new predictive equations and subsequent suggestions for solutions have been derived from this research topic based on the newly obtained experimental results. The proposed models and procedures make it possible to get new results and insights into coating technologies.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/LO1502" target="_blank" >LO1502: Rozvoj Regionálního technologického institutu</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Applied Sciences

ISSN

2076-3417

e-ISSN

—

Svazek periodika

10

Číslo periodika v rámci svazku

7

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

23

Strana od-do

—

Kód UT WoS článku

000533356200323

EID výsledku v databázi Scopus

2-s2.0-85083483107