Measurement and evaluation of shaft torsional vibrations using shaft instantaneous angular velocity

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23520%2F19%3A43951775" target="_blank" >RIV/49777513:23520/19:43951775 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.scopus.com/record/display.uri?eid=2-s2.0-85058436733" target="_blank" >https://www.scopus.com/record/display.uri?eid=2-s2.0-85058436733</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1115/1.4041006" target="_blank" >10.1115/1.4041006</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Measurement and evaluation of shaft torsional vibrations using shaft instantaneous angular velocity

Popis výsledku v původním jazyce

Online evaluation of possible failures of a turbine is a key factor for a successful long-term turbine operation. Fluctuations of generator air-gap torque, caused for example by non-stationary conditions of electrical power grid, influence shaft torsional vibrations as well as rotating blades vibrations. Symptoms of shaft torsional vibrations are not measurable by normally used relative shaft vibrations sensors, so special measurement must be used. The direct consequence of shaft torsional vibrations is local acceleration or deceleration of shaft circumference when it is measured by a stationary sensor. This article deals with a measurement method using an optical probe measuring the passage of black and white stripes of a zebra tape which is stuck on the rotor. The shaft torsional vibrations manifest themselves as a phase modulation of the optical probe output signal, so the sampling rate influence the achievable resolution of the calculated shaft vibrations. The presented method for the calculation of the shaft torsional vibrations is based on the evaluation of shaft instantaneous angular velocity. The advantage of this method is a direct compensation of possible non-regular geometry of the zebra tape. The analysis of shaft torsional vibrations evaluation using this method is supplemented by two case studies from the authors’ current work.

Název v anglickém jazyce

Measurement and evaluation of shaft torsional vibrations using shaft instantaneous angular velocity

Popis výsledku anglicky

Online evaluation of possible failures of a turbine is a key factor for a successful long-term turbine operation. Fluctuations of generator air-gap torque, caused for example by non-stationary conditions of electrical power grid, influence shaft torsional vibrations as well as rotating blades vibrations. Symptoms of shaft torsional vibrations are not measurable by normally used relative shaft vibrations sensors, so special measurement must be used. The direct consequence of shaft torsional vibrations is local acceleration or deceleration of shaft circumference when it is measured by a stationary sensor. This article deals with a measurement method using an optical probe measuring the passage of black and white stripes of a zebra tape which is stuck on the rotor. The shaft torsional vibrations manifest themselves as a phase modulation of the optical probe output signal, so the sampling rate influence the achievable resolution of the calculated shaft vibrations. The presented method for the calculation of the shaft torsional vibrations is based on the evaluation of shaft instantaneous angular velocity. The advantage of this method is a direct compensation of possible non-regular geometry of the zebra tape. The analysis of shaft torsional vibrations evaluation using this method is supplemented by two case studies from the authors’ current work.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20205 - Automation and control systems

Projekt

<a href="/cs/project/LO1506" target="_blank" >LO1506: Podpora udržitelnosti centra NTIS - Nové technologie pro informační společnost</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME

ISSN

0742-4795

e-ISSN

—

Svazek periodika

141

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

US - Spojené státy americké

Počet stran výsledku

5

Strana od-do

041029-1- 041029-5

Kód UT WoS článku

000462020200029

EID výsledku v databázi Scopus

2-s2.0-85058436733