Influence of Machining Parameters on the Surface Quality of Technical Plastics
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60162694%3AG43__%2F21%3A00557781" target="_blank" >RIV/60162694:G43__/21:00557781 - isvavai.cz</a>
Výsledek na webu
<a href="https://iopscience.iop.org/article/10.1149/10501.0381ecst" target="_blank" >https://iopscience.iop.org/article/10.1149/10501.0381ecst</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1149/10501.0381ecst" target="_blank" >10.1149/10501.0381ecst</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Influence of Machining Parameters on the Surface Quality of Technical Plastics
Popis výsledku v původním jazyce
The article deals with the evaluation of the influence of conventional methods of machining on the surface quality of selected technical plastics. The thermoplastic polymer polyoximethylene (POM-C) Ertacetal C and polyamide (PA 6) Ertalon 6SA were selected for machining. Both materials are suitable for machining and are used for the production of precision mechanical components (e.g. gears, plain bearings, guides, etc.), but also in electronics and electrical engineering. In all these applications, the quality of machined surfaces is important, especially for functional surfaces that interact with other surfaces. Test specimens from these materials were turned and milled. The technological conditions of machining (revolutions per minute n, cutting speed v c , feed f, depth of cut a p ) were adapted to achieve approximately the same surface roughness values. The milled samples were machined with and without cooling medium (for drought). Turning was performed only dry. As the cutting speed v c increased, the surface roughness of the turned Ertacetal C material decreased, while milling led to a deterioration in the roughness as the cutting speed v c increased. Similar behavior was observed for Ertalon 6SA. The process fluid led to a deterioration in the roughness of the milled surfaces of both plastics. Turned surfaces showed worse roughness than milled surfaces.
Název v anglickém jazyce
Influence of Machining Parameters on the Surface Quality of Technical Plastics
Popis výsledku anglicky
The article deals with the evaluation of the influence of conventional methods of machining on the surface quality of selected technical plastics. The thermoplastic polymer polyoximethylene (POM-C) Ertacetal C and polyamide (PA 6) Ertalon 6SA were selected for machining. Both materials are suitable for machining and are used for the production of precision mechanical components (e.g. gears, plain bearings, guides, etc.), but also in electronics and electrical engineering. In all these applications, the quality of machined surfaces is important, especially for functional surfaces that interact with other surfaces. Test specimens from these materials were turned and milled. The technological conditions of machining (revolutions per minute n, cutting speed v c , feed f, depth of cut a p ) were adapted to achieve approximately the same surface roughness values. The milled samples were machined with and without cooling medium (for drought). Turning was performed only dry. As the cutting speed v c increased, the surface roughness of the turned Ertacetal C material decreased, while milling led to a deterioration in the roughness as the cutting speed v c increased. Similar behavior was observed for Ertalon 6SA. The process fluid led to a deterioration in the roughness of the milled surfaces of both plastics. Turned surfaces showed worse roughness than milled surfaces.
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
—
OECD FORD obor
20300 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach<br>I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace
Ostatní
Rok uplatnění
2021
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
ECS Transactions
ISBN
978-1-6076-8539-5
ISSN
1938-6737
e-ISSN
1938-6737
Počet stran výsledku
9
Strana od-do
381-389
Název nakladatele
IOP Publishing Ltd
Místo vydání
Bristol, Velká Británie
Místo konání akce
Brno, Czech Republic
Datum konání akce
22. 8. 2021
Typ akce podle státní příslušnosti
WRD - Celosvětová akce
Kód UT WoS článku
—