Evaluation of the Effect of Machining Technologies on the Surface Texture Analysis of Ertacetal C Polymer
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28120%2F22%3A63552578" target="_blank" >RIV/70883521:28120/22:63552578 - isvavai.cz</a>
Výsledek na webu
<a href="https://journalmt.com/artkey/mft-202206-0008_evaluation-of-the-effect-of-machining-technologies-on-the-surface-texture-analysis-of-ertacetal-c-polymer.php" target="_blank" >https://journalmt.com/artkey/mft-202206-0008_evaluation-of-the-effect-of-machining-technologies-on-the-surface-texture-analysis-of-ertacetal-c-polymer.php</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.21062/mft.2022.083" target="_blank" >10.21062/mft.2022.083</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Evaluation of the Effect of Machining Technologies on the Surface Texture Analysis of Ertacetal C Polymer
Popis výsledku v původním jazyce
The surface created by machining significantly affects the service life and functional reliability of the component. As part of this study, four different chip machining technologies were evaluated on the surface texture of the polymer material Ertacetal C. The samples were processed by turning, milling, grinding and polishing technologies, 5 samples for each technology. Within the given technology, different cutting conditions were chosen to compare the effect of cutting conditions on the resulting surface roughness. The machined surfaces were comprehensively evaluated on the basis of 16 profile and surface roughness parameters due to the practical use of the tested material. Surface texture measurements were performed on a Talysurf CCI Lite device. A non-contact method using a coher-ence correlation interferometer was used for the measurement. The obtained data were evaluated using TalyMap Platinum software. Graphical documentation of the machined surfaces was made using an Olympus DSX500 opto-digital metallographic microscope.
Název v anglickém jazyce
Evaluation of the Effect of Machining Technologies on the Surface Texture Analysis of Ertacetal C Polymer
Popis výsledku anglicky
The surface created by machining significantly affects the service life and functional reliability of the component. As part of this study, four different chip machining technologies were evaluated on the surface texture of the polymer material Ertacetal C. The samples were processed by turning, milling, grinding and polishing technologies, 5 samples for each technology. Within the given technology, different cutting conditions were chosen to compare the effect of cutting conditions on the resulting surface roughness. The machined surfaces were comprehensively evaluated on the basis of 16 profile and surface roughness parameters due to the practical use of the tested material. Surface texture measurements were performed on a Talysurf CCI Lite device. A non-contact method using a coher-ence correlation interferometer was used for the measurement. The obtained data were evaluated using TalyMap Platinum software. Graphical documentation of the machined surfaces was made using an Olympus DSX500 opto-digital metallographic microscope.
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace
Ostatní
Rok uplatnění
2022
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Manufacturing Technology
ISSN
1213-2489
e-ISSN
2787-9402
Svazek periodika
22
Číslo periodika v rámci svazku
6
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
14
Strana od-do
679-692
Kód UT WoS článku
000908397300004
EID výsledku v databázi Scopus
2-s2.0-85146723973