Resistance spot welding of steel sheets of the same and different thickness

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41310%2F17%3A73914" target="_blank" >RIV/60460709:41310/17:73914 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.11118/actaun201765030807" target="_blank" >http://dx.doi.org/10.11118/actaun201765030807</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.11118/actaun201765030807" target="_blank" >10.11118/actaun201765030807</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Resistance spot welding of steel sheets of the same and different thickness

Popis výsledku v původním jazyce

Resistance welding ranks among progressive and in practice often used manufacturing techniques of rigid joints. It is applied in single-part production, short-run production as well as in mass production. The basis of this method is in the utilization of the Joulean heat, which arises at the passage of current through connected sheets at collective influence of compressive force. The aim of the carried out tests was the determination of the dependence between the rupture force of spot welds made using steel sheets of the same and different thickness for different welding conditions. For carrying out of this aim 360 assemblies were prepared. The sheets (a total of 720 pieces) of dimensions 100 x 25 mm and thickness of 0,8 mm, 1,5 mm and 3,0 mm were made from low carbon steel. In the place determined for welding the test specimens were garnet blasted and then degreased with acetone. The welding of two specimens always of the same (0,8+0,8 mm, 1,5+1,5 mm a 3,0+3,0 mm) and different (0,8+1,5 mm, 0,8+3,0

Název v anglickém jazyce

Resistance spot welding of steel sheets of the same and different thickness

Popis výsledku anglicky

Resistance welding ranks among progressive and in practice often used manufacturing techniques of rigid joints. It is applied in single-part production, short-run production as well as in mass production. The basis of this method is in the utilization of the Joulean heat, which arises at the passage of current through connected sheets at collective influence of compressive force. The aim of the carried out tests was the determination of the dependence between the rupture force of spot welds made using steel sheets of the same and different thickness for different welding conditions. For carrying out of this aim 360 assemblies were prepared. The sheets (a total of 720 pieces) of dimensions 100 x 25 mm and thickness of 0,8 mm, 1,5 mm and 3,0 mm were made from low carbon steel. In the place determined for welding the test specimens were garnet blasted and then degreased with acetone. The welding of two specimens always of the same (0,8+0,8 mm, 1,5+1,5 mm a 3,0+3,0 mm) and different (0,8+1,5 mm, 0,8+3,0

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20306 - Audio engineering, reliability analysis

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis

ISSN

1211-8516

e-ISSN

2464-8310

Svazek periodika

65

Číslo periodika v rámci svazku

3

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

8

Strana od-do

807-814

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85021789904