Research on application of technology using water jet on machining of polymeric composite biological-reinforced materials

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41310%2F18%3A77624" target="_blank" >RIV/60460709:41310/18:77624 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.21062/ujep/152.2018/a/1213-2489/MT/18/4/630" target="_blank" >http://dx.doi.org/10.21062/ujep/152.2018/a/1213-2489/MT/18/4/630</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.21062/ujep/152.2018/a/1213-2489/MT/18/4/630" target="_blank" >10.21062/ujep/152.2018/a/1213-2489/MT/18/4/630</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Research on application of technology using water jet on machining of polymeric composite biological-reinforced materials

Popis výsledku v původním jazyce

The paper deals with a machining of polymeric composite materials reinforced with fibres from hemp, false banana (Ensete ventricosum) and microparticles from Jatropha Curcas L. seedcakes by means of a technology using a water jet (abrasive water jet AWJ, water jet WJ). A matrix of the composite material is from a structural resin used for a production of sport equipment which shows good mechanical properties, but is it very brittle and it comes to its destruction during machining. Therefore, the water jet technology was used for the research. The research was focused on the evaluation of an influence of a velocity of a cutting head movement on a kerf width inlet and outlet the composite board by means of an optical analysis and on a connected quality of the cut. The composite material based on the biological reinforcement was cut by CNS cutting machine AWJ CT 0806 at a different velocity of the cutting head movement (traverse speed), i.e. 50, 250, 750 and 1000 mm/min. The research results proved a si

Název v anglickém jazyce

Research on application of technology using water jet on machining of polymeric composite biological-reinforced materials

Popis výsledku anglicky

The paper deals with a machining of polymeric composite materials reinforced with fibres from hemp, false banana (Ensete ventricosum) and microparticles from Jatropha Curcas L. seedcakes by means of a technology using a water jet (abrasive water jet AWJ, water jet WJ). A matrix of the composite material is from a structural resin used for a production of sport equipment which shows good mechanical properties, but is it very brittle and it comes to its destruction during machining. Therefore, the water jet technology was used for the research. The research was focused on the evaluation of an influence of a velocity of a cutting head movement on a kerf width inlet and outlet the composite board by means of an optical analysis and on a connected quality of the cut. The composite material based on the biological reinforcement was cut by CNS cutting machine AWJ CT 0806 at a different velocity of the cutting head movement (traverse speed), i.e. 50, 250, 750 and 1000 mm/min. The research results proved a si

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20505 - Composites (including laminates, reinforced plastics, cermets, combined natural and synthetic fibre fabrics; filled composites)

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2018

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

18

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

5

Strana od-do

630-634

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85058060890