ADHESION OF BIOCOMPATIBLE TiNb COATING
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61389021%3A_____%2F17%3A00477605" target="_blank" >RIV/61389021:_____/17:00477605 - isvavai.cz</a>
Výsledek na webu
<a href="http://dx.doi.org/10.14311/APP.2017.8.0005" target="_blank" >http://dx.doi.org/10.14311/APP.2017.8.0005</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.14311/APP.2017.8.0005" target="_blank" >10.14311/APP.2017.8.0005</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
ADHESION OF BIOCOMPATIBLE TiNb COATING
Popis výsledku v původním jazyce
Preparation of a coating with a high quality requires good adhesion of the film to the substrate. The paper deals with the adhesion of biocompatible TiNb coating with different base materials. Several materials such as titanium CP grade 2, titanium alloys Ti6Al4V and stainless steel AISI 316L were measured. Testing samples were made in the shape of small discs. Those samples were coated with a TiNb layer by using the PVD method (magnetron sputtering). Onto the measured layer of TiNb an assistant cylinder was stuck using a high strength epoxy adhesive E1100S. The sample with the assistant cylinder was fixed into a special fixture and the whole assembly underwent pull-off testing for adhesion. The main result of this experiment was determining the strength needed to peel the layer and morphology and size of the breakaway. As a result, we will be able to determine the best base material and conditions where the coating will be remain intact with the base material.
Název v anglickém jazyce
ADHESION OF BIOCOMPATIBLE TiNb COATING
Popis výsledku anglicky
Preparation of a coating with a high quality requires good adhesion of the film to the substrate. The paper deals with the adhesion of biocompatible TiNb coating with different base materials. Several materials such as titanium CP grade 2, titanium alloys Ti6Al4V and stainless steel AISI 316L were measured. Testing samples were made in the shape of small discs. Those samples were coated with a TiNb layer by using the PVD method (magnetron sputtering). Onto the measured layer of TiNb an assistant cylinder was stuck using a high strength epoxy adhesive E1100S. The sample with the assistant cylinder was fixed into a special fixture and the whole assembly underwent pull-off testing for adhesion. The main result of this experiment was determining the strength needed to peel the layer and morphology and size of the breakaway. As a result, we will be able to determine the best base material and conditions where the coating will be remain intact with the base material.
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
—
OECD FORD obor
20503 - Textiles; including synthetic dyes, colours, fibres (nanoscale materials to be 2.10; biomaterials to be 2.9)
Návaznosti výsledku
Projekt
—
Návaznosti
I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace
Ostatní
Rok uplatnění
2017
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
Acta Polytechnica CTU Proceedings
ISBN
978-80-01-06135-0
ISSN
2336-5382
e-ISSN
—
Počet stran výsledku
3
Strana od-do
5-7
Název nakladatele
Czech Technical University in Prague
Místo vydání
Praha
Místo konání akce
Herbertov
Datum konání akce
20. 9. 2016
Typ akce podle státní příslušnosti
EUR - Evropská akce
Kód UT WoS článku
—