Fracture Toughness of Cold Sprayed Pure Metals

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61389021%3A_____%2F20%3A00531001" target="_blank" >RIV/61389021:_____/20:00531001 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/68407700:21340/20:00339675 RIV/00216305:26210/20:PU147634

Výsledek na webu

<a href="https://link.springer.com/article/10.1007%2Fs11666-019-00956-z" target="_blank" >https://link.springer.com/article/10.1007%2Fs11666-019-00956-z</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/s11666-019-00956-z" target="_blank" >10.1007/s11666-019-00956-z</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Fracture Toughness of Cold Sprayed Pure Metals

Popis výsledku v původním jazyce

The study of fracture toughness of pure Al, Cu, Ni and Ti deposited by cold spray was performed in order to obtain a fundamental understanding of the damage process and quantify the material performance. Rectangular specimens cut from self-standing deposits with fatigue pre-cracks were tested in three-point bending. The KIC values were obtained from J-R curves following the ASTM E1820 standard. The stress–strain behavior of the tested material was obtained from supplementary four-point bending. The cold spray deposits exhibited significantly lower fracture toughness than the corresponding wrought materials. The reduction was more pronounced for coatings with limited ductility (Ti and Cu), where the fracture toughness reached less than 12% of the wrought counterpart only. The higher ductility coatings of Al and Ni possessed fracture toughness of 18–25% of the wrought reference materials. The performed fractographic analysis revealed inter-particular decohesion as the major failure mode.

Název v anglickém jazyce

Fracture Toughness of Cold Sprayed Pure Metals

Popis výsledku anglicky

The study of fracture toughness of pure Al, Cu, Ni and Ti deposited by cold spray was performed in order to obtain a fundamental understanding of the damage process and quantify the material performance. Rectangular specimens cut from self-standing deposits with fatigue pre-cracks were tested in three-point bending. The KIC values were obtained from J-R curves following the ASTM E1820 standard. The stress–strain behavior of the tested material was obtained from supplementary four-point bending. The cold spray deposits exhibited significantly lower fracture toughness than the corresponding wrought materials. The reduction was more pronounced for coatings with limited ductility (Ti and Cu), where the fracture toughness reached less than 12% of the wrought counterpart only. The higher ductility coatings of Al and Ni possessed fracture toughness of 18–25% of the wrought reference materials. The performed fractographic analysis revealed inter-particular decohesion as the major failure mode.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/EF16_019%2F0000778" target="_blank" >EF16_019/0000778: Centrum pokročilých aplikovaných přírodních věd</a><br>

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Journal of Thermal Spray Technology

ISSN

1059-9630

e-ISSN

—

Svazek periodika

29

Číslo periodika v rámci svazku

1-2

Stát vydavatele periodika

US - Spojené státy americké

Počet stran výsledku

11

Strana od-do

147-157

Kód UT WoS článku

000496259400006

EID výsledku v databázi Scopus

2-s2.0-85075211576