Evaluation of Residual Stresses after Irregular Interrupted Machining
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F18%3A10239067" target="_blank" >RIV/61989100:27230/18:10239067 - isvavai.cz</a>
Nalezeny alternativní kódy
RIV/61989100:27230/19:10239404
Výsledek na webu
<a href="https://hrcak.srce.hr/204446" target="_blank" >https://hrcak.srce.hr/204446</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.17559/TV-20160615125650" target="_blank" >10.17559/TV-20160615125650</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Evaluation of Residual Stresses after Irregular Interrupted Machining
Popis výsledku v původním jazyce
Residual stress occurs in many machined components and parts. Over time, several methods have been developed for the investigation of residual stress in the material - destructive and non-destructive. This article deals with the evaluation and comparison of residual stress in the material when machining steel C45 and 11CrMo9-10, when the tool enters into the cut and stands out in conditions of an interrupted cut. A non-destructive method, based on X-Ray diffraction, was applied to evaluate the residual stress. The points were measured on the last machined slat by using interrupted cut simulator. An irregular interrupted cut was achieved by gradually machining 4, 3, 2 and 1 slat. The experiments were realized in co-operation with the Faculty of Mechanical Engineering, VSB - Technical University of Ostrava, Czech Republic and the Faculty of Mechanical Engineering, the University of Zilina, Slovakia.
Název v anglickém jazyce
Evaluation of Residual Stresses after Irregular Interrupted Machining
Popis výsledku anglicky
Residual stress occurs in many machined components and parts. Over time, several methods have been developed for the investigation of residual stress in the material - destructive and non-destructive. This article deals with the evaluation and comparison of residual stress in the material when machining steel C45 and 11CrMo9-10, when the tool enters into the cut and stands out in conditions of an interrupted cut. A non-destructive method, based on X-Ray diffraction, was applied to evaluate the residual stress. The points were measured on the last machined slat by using interrupted cut simulator. An irregular interrupted cut was achieved by gradually machining 4, 3, 2 and 1 slat. The experiments were realized in co-operation with the Faculty of Mechanical Engineering, VSB - Technical University of Ostrava, Czech Republic and the Faculty of Mechanical Engineering, the University of Zilina, Slovakia.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2018
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Tehnički vjesnik – Technical Gazette
ISSN
1330-3651
e-ISSN
—
Svazek periodika
25
Číslo periodika v rámci svazku
4
Stát vydavatele periodika
HR - Chorvatská republika
Počet stran výsledku
5
Strana od-do
1009-1013
Kód UT WoS článku
000442273000009
EID výsledku v databázi Scopus
2-s2.0-85052197841