Evaluation of Residual Stresses after Irregular Interrupted Machining

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F19%3A10239404" target="_blank" >RIV/61989100:27230/19:10239404 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/61989100:27230/18:10239067

Výsledek na webu

<a href="http://hhttps://www.researchgate.net/publication/327385283_Evaluation_of_Residual_Stresses_after_Irregular_Interrupted_Machi" target="_blank" >http://hhttps://www.researchgate.net/publication/327385283_Evaluation_of_Residual_Stresses_after_Irregular_Interrupted_Machi</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.17559/TV-20160615125650" target="_blank" >10.17559/TV-20160615125650</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Evaluation of Residual Stresses after Irregular Interrupted Machining

Popis výsledku v původním jazyce

Residual stress occurs in many machined components and parts. Over time, several methods have been developed for the investigation of residual stress in the material - destructive and non-destructive. This article deals with the evaluation and comparison of residual stress in the material when machining steel C45 and 11CrMo9-10, when the tool enters into the cut and stands out in conditions of an interrupted cut. A non-destructive method, based on X-Ray diffraction, was applied to evaluate the residual stress. The points were measured on the last machined slat by using interrupted cut simulator. An irregular interrupted cut was achieved by gradually machining 4, 3, 2 and 1 slat. The experiments were realized in co-operation with the Faculty of Mechanical Engineering, VSB - Technical University of Ostrava, Czech Republic and the Faculty of Mechanical Engineering, the University of Zilina, Slovakia.

Název v anglickém jazyce

Evaluation of Residual Stresses after Irregular Interrupted Machining

Popis výsledku anglicky

Residual stress occurs in many machined components and parts. Over time, several methods have been developed for the investigation of residual stress in the material - destructive and non-destructive. This article deals with the evaluation and comparison of residual stress in the material when machining steel C45 and 11CrMo9-10, when the tool enters into the cut and stands out in conditions of an interrupted cut. A non-destructive method, based on X-Ray diffraction, was applied to evaluate the residual stress. The points were measured on the last machined slat by using interrupted cut simulator. An irregular interrupted cut was achieved by gradually machining 4, 3, 2 and 1 slat. The experiments were realized in co-operation with the Faculty of Mechanical Engineering, VSB - Technical University of Ostrava, Czech Republic and the Faculty of Mechanical Engineering, the University of Zilina, Slovakia.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20300 - Mechanical engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Tehnički vjesnik – Technical Gazette

ISSN

1330-3651

e-ISSN

—

Svazek periodika

25

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

HR - Chorvatská republika

Počet stran výsledku

4

Strana od-do

1009-1013

Kód UT WoS článku

000442273000009

EID výsledku v databázi Scopus

—